- 您現在的位置：買賣IC網 > PDF目錄6039 > ADA4940-2ACPZ-R7 (Analog Devices Inc)IC DIFF ADC DVR 18BIT LN 24LFCSP PDF資料下載
參數資料
| 型號： | ADA4940-2ACPZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DIFF ADC DVR 18BIT LN 24LFCSP |
| 特色產品： | ADA4940 Amplifiers |
| 標準包裝： | 1 |
| 放大器類型： | 差分 |
| 電路數： | 2 |
| 輸出類型： | 差分 |
| 轉換速率： | 95 V/µs |
| -3db帶寬： | 260MHz |
| 電流 - 輸入偏壓： | 1.1µA |
| 電壓 - 輸入偏移： | 60µV |
| 電流 - 電源： | 1.25mA |
| 電流 - 輸出 / 通道： | 46mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 7 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 24-LFCSP-VQ（4x4） |
| 包裝： | 標準包裝 |
| 其它名稱： | ADA4940-2ACPZ-R7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
ADA4940-1/ADA4940-2
Data Sheet
Rev. C | Page 26 of 32
INPUT AND OUTPUT CAPACITIVE AC COUPLING
Although the ADA4940-1/ADA4940-2 is best suited to dc-
coupled applications, it is nonetheless possible to use it in ac-
coupled circuits. Input ac coupling capacitors can be inserted
between the source and RG. This ac coupling blocks the flow
of the dc common-mode feedback current and causes the
ADA4940-1/ADA4940-2 dc input common-mode voltage to
equal the dc output common-mode voltage. These ac coupling
capacitors must be placed in both loops to keep the feedback
factors matched. Output ac coupling capacitors can be placed in
series between each output and its respective load.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
biased at a voltage approximately equal to the midsupply point,
[(+VS) + (VS)]/2. Relying on this internal bias results in an
output common-mode voltage that is within approximately
100 mV of the expected value.
In cases where more accurate control of the output common-mode
level is required, it is recommended that an external source, or
resistor divider (10 k or greater resistors), be used. The output
common-mode offset listed in the Specifications section assumes
that the VOCM input is driven by a low impedance voltage source.
It is also possible to connect the VOCM input to a common-mode
level (CML) output of an ADC. However, care must be taken to
ensure that the output has sufficient drive capability. The input
impedance of the VOCM pin is approximately 250 k.
DISABLE PIN
The ADA4940-1/ADA4940-2 feature a DISABLE pin that can
be used to minimize the quiescent current consumed when the
device is not being used. DISABLE is asserted by applying a low
logic level to the DISABLE pin. The threshold between high and
low logic levels is nominally 1.4 V above the negative supply rail.
See Table 5 and Table 8 for the threshold limits.
The DISABLE pin features an internal pull-up network that
enables the amplifier for normal operation. The ADA4940-1/
ADA4940-2 DISABLE pin can be left floating (that is, no
external connection is required) and does not require an
external pull-up resistor to ensure normal on operation (see
output is high impedance. Note that the outputs are tied to the
inputs through the feedback resistors and to the source using the
gain resistors. In addition, there are back-to-back diodes on the
input pins that limit the differential voltage to 1.2 V.
08452-
063
DISABLE
AMPLIFIER
BIAS CURRENT
–VS
+VS
Figure 70. DISABLE Pin Circuit
DRIVING A CAPACITIVE LOAD
A purely capacitive load reacts with the bond wire and pin
inductance of the ADA4940-1/ADA4940-2, resulting in high
frequency ringing in the transient response and loss of phase
margin. One way to minimize this effect is to place a resistor in
series with each output to buffer the load capacitance. The resistor
and load capacitance form a first-order, low-pass filter; therefore,
the resistor value should be as small as possible. In some cases,
the ADCs require small series resistors to be added on their inputs.
Figure 71 illustrates the capacitive load vs. the series resistance
required to maintain a minimum 45° of phase margin.
120
0
5
100
10
1000
08452-
064
20
40
60
80
100
SER
IES
R
ESI
ST
A
N
C
E
(
)
LOAD CAPACITANCE (pF)
+IN
–OUT
+OUT
–FB
+FB
–IN
VOCM
0.1F
RS
RS
R1
CL
R2
R4
+2.5V
–2.5V
R3
VIN
Figure 71. Capacitive Load vs. Series Resistance (LFSCP)
相關PDF資料 |
PDF描述 |
|---|---|
| PBC10SFCN | CONN HEADER .100 SINGL STR 10POS |
| TFML-140-02-S-D | CONN HEADER .05" 80POS DUAL SMD |
| PBC13SFBN | CONN HEADER .100 SINGL STR 13POS |
| AD627ANZ | IC AMP INST R-R 25MA 8DIP |
| LT1206CN8#PBF | IC CURRNT FEEDBCK AMP 250MA 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4940-2ACPZ-RL | 功能描述:IC DIFF ADC DVR 18BIT LN 24LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| ADA4941 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR, Differential ADC in MSOP |
| ADA4941-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power |
| ADA4941-1YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4941-1YCP RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ADA4941-1YCPZ-R2 | 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single R-R O/P 12V 8-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single R-R O/P 12V 8-Pin LFCSP EP Tape & Reel |
發布緊急采購，3分鐘左右您將得到回復。