- 您現在的位置：買賣IC網 > PDF目錄378280 > ADC088S102EVAL (National Semiconductor Corporation) 8-Channel, 500 kSPS to 1 MSPS, 8-Bit A/D Converter PDF資料下載
參數資料
| 型號： | ADC088S102EVAL |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 8-Channel, 500 kSPS to 1 MSPS, 8-Bit A/D Converter |
| 中文描述： | 8通道，500 kSPS的1 MSPS的，8位A / D轉換器 |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 830K |
| 代理商： | ADC088S102EVAL |
Specification Definitions
ACQUISITION TIME
is the time required for the ADC to
acquire the input voltage. During this time, the hold capacitor
is charged by the input voltage.
APERTURE DELAY
is the time between the fourth falling
edge of SCLK and the time when the input signal is internally
acquired or held for conversion.
CONVERSION TIME
is the time required, after the input
voltage is acquired, for the ADC to convert the input voltage
to a digital word.
CHANNEL-TO-CHANNEL ISOLATION
is resistance to cou-
pling of energy from one channel into another channel.
CROSSTALK
is the coupling of energy from one channel
into another channel. This is similar to Channel-to-Channel
Isolation, except for the sign of the data.
DIFFERENTIAL NON-LINEARITY (DNL)
is the measure of
the maximum deviation from the ideal step size of 1 LSB.
DUTY CYCLE
is the ratio of the time that a repetitive digital
waveform is high to the total time of one period. The speci-
fication here refers to the SCLK.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS)
is another method of specifying Signal-to-Noise and
Distortion or SINAD. ENOB is defined as (SINAD - 1.76) /
6.02 and says that the converter is equivalent to a perfect
ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH
is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its low frequency value for a full scale input.
GAIN ERROR
is the deviation of the last code transition
(111...110) to (111...111) from the ideal (V
REF
- 1.5 LSB),
after adjusting for offset error.
INTEGRAL NON-LINEARITY (INL)
is a measure of the
deviation of each individual code from a line drawn from
negative full scale (
1
2
LSB below the first code transition)
through positive full scale (
1
2
LSB above the last code
transition). The deviation of any given code from this straight
line is measured from the center of that code value.
INTERMODULATION DISTORTION (IMD)
is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to an individual ADC input at the
same time. It is defined as the ratio of the power in either the
second or the third order intermodulation products to the
sum of the power in both of the original frequencies. Second
order products are f
±
f
, where f
and f
are the two sine
wave input frequencies. Third order products are (2f
a
±
f
b
)
and (f
a
±
2f
b
). IMD is usually expressed in dB.
MISSING CODES
are those output codes that will never
appear at the ADC outputs. The ADC088S102 is guaranteed
not to have any missing codes.
OFFSET ERROR
is the deviation of the first code transition
(000...000) to (000...001) from the ideal (i.e. GND + 0.5
LSB).
SIGNAL TO NOISE RATIO (SNR)
is the ratio, expressed in
dB, of the rms value of the input signal to the rms value of the
sum of all other spectral components below one-half the
sampling frequency, not including harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD)
Is the ratio, expressed in dB, of the rms value of the input
signal to the rms value of all of the other spectral compo-
nents below half the clock frequency, including harmonics
but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
is the differ-
ence, expressed in dB, between the rms values of the input
signal and the peak spurious signal where a spurious signal
is any signal present in the output spectrum that is not
present at the input, including harmonics but excluding d.c.
TOTAL HARMONIC DISTORTION (THD)
is the ratio, ex-
pressed in dBc, of the rms total of the first five harmonic
components at the output to the rms level of the input signal
frequency as seen at the output. THD is calculated as
where A
is the RMS power of the input frequency at the
output and A
through A
f6
are the RMS power in the first 5
harmonic frequencies.
THROUGHPUT TIME
is the minimum time required between
the start of two successive conversions. It is the acquisition
time plus the conversion time.
A
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| ADC1001CCJ-1 | RES 27K 1/4W 5% CF |
| ADC1001 | 10-Bit P Compatible A/D Converter |
| ADC1001CCJ | 10-Bit P Compatible A/D Converter |
| ADC10030CIVT | 10-Bit, 30 MSPS, 125 mW A/D Converter with Internal Sample and Hold |
| ADC10030 | 10-Bit, 30 MSPS, 125 mW A/D Converter with Internal Sample and Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC08B200CIVS | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08B200CIVS/NOPB | 功能描述:模數轉換器 - ADC 8B,200 MSPS ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08B200EB | 功能描述:BOARD EVAL FOR ADC08B200 TQFP RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| ADC08B200QCIVS/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08B3000CIYB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。