- 您現在的位置：買賣IC網 > PDF目錄378281 > ADC10221 (National Semiconductor Corporation) 10-Bit, 15 MSPS, 98 mW A/D Converter with Internal Sample and Hold PDF資料下載
參數資料
| 型號： | ADC10221 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 10-Bit, 15 MSPS, 98 mW A/D Converter with Internal Sample and Hold |
| 中文描述： | 10位，15 MSPS的98毫瓦的A / D內部采樣與保持器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 414K |
| 代理商： | ADC10221 |
Applications Information
(Continued)
The V
+ F and V
F pins should each be bypassed to
AGND with 10 μF tantalum or electrolytic and 0.1 μF ceramic
capacitors. The circuit of Figure 6may be used if it is desired
to obtain precise reference voltages. The LMC6082 in this
circuit was chosen for its low offset voltage, low voltage ca-
pability and low cost.
Since the current flowing through the sense lines (those lines
associated with V
+ S and V
S) is essentially zero,
there is negligible voltage drop across any resistance in se-
ries with these sense pins and the voltage at the inverting in-
put of the op-amp accurately represents the voltage at the
top (or bottom) of the ladder. The op-amp drives the force in-
put, forcing the voltage at the ends of the ladder to equal the
voltage at the op-amp’s non-inverting input, plus any offset
voltage. For this reason, op-amps with low V
OS
, such as the
LMC6081 and LMC6082, should be used for this application.
Voltages at the reference sense pins (V
+ S and V
S)
should be within the range specified in the Operating Ratings
table (2.3V to 4.0V for V
+ and 1.3V to 3.0V for V
).
Any device used to drive the reference pins should be able to
source sufficient current into the V
+ F pin and sink suffi-
cient current from the V
F pin when the ladder is at its
minimum value of 850 Ohms.
The reference voltage at the top of the ladder (V
+) may
take on values as low as 1.0V above the voltage at the bot-
tom of the ladder (V
) and as high as (V
A
- 1.0V) Volts.
The voltage at the bottom of the ladder (V
) may take on
values as low as 1.3 Volts and as high as 3.0V. However, to
minimize noise effects and ensure accurate conversions, the
total reference voltage range (V
REF
+ - V
REF
) should be a
minimum of 2.0V and a maximum of 2.7V.
DS101038-19
FIGURE 5. Better low component count reference biasing
A
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| ADC102S021 | 2 Channel, 1 MSPS 12-Bit A/D Converter |
| ADC102S051 | 2 Channel, 1 MSPS 12-Bit A/D Converter |
| ADC102S101 | 2 Channel, 1 MSPS 12-Bit A/D Converter |
| ADC122S021 | 2 Channel, 1 MSPS 12-Bit A/D Converter |
| ADC122S051 | 2 Channel, 1 MSPS 12-Bit A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC10221CIVT | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit, 15 MSPS, 98 mW A/D Converter with Internal Sample and Hold |
| ADC10221EVAL | 功能描述:BOARD EVALUATION FOR ADC10221 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADC1025 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-BIT uP COMPATIBLE A/D CONVERTERS |
| ADC1025BCJ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-BIT uP COMPATIBLE A/D CONVERTERS |
| ADC1025BCJ/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
發布緊急采購，3分鐘左右您將得到回復。