- 您現在的位置：買賣IC網 > PDF目錄378281 > ADC10461 (National Semiconductor Corporation) 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold PDF資料下載
參數資料
| 型號： | ADC10461 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| 中文描述： | 10位600納秒的A / D輸入多路復用器和轉換器采樣/保持 |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 342K |
| 代理商： | ADC10461 |
Applications Information
(Continued)
tive. When S /H goes high, the result of the coarse conver-
sion is latched and the “fine” conversion begins. After 600 ns
(typical), INT goes low, indicating that the conversion results
are latched and can be read by pulling RD low. Note that CS
must be low to enable S /H or RD. CS is internally “ANDed”
with S /H and RD; the input voltage is sampled when CS and
S /H are low, and data is read when CS and RD are low. INT
is reset high on the rising edge of RD.
TABLE 1. Input Multiplexer Programming
ADC10464
S
1
0
0
1
1
S
0
0
1
0
1
Channel
V
IN0
V
IN1
V
IN2
V
IN3
TABLE 2. Input Multiplexer Programming
ADC10462
S
0
0
1
Channel
V
IN0
V
IN1
Mode 2
In Mode 2, also called “RD mode”, the S /H and RD pins are
tied together. A conversion is initiated by pulling both pins
low. The A/D converter samples the input voltage and
causes the coarse comparators to become active. An inter-
nal timer then terminates the coarse conversion and begins
the fine conversion. 850 ns (typical) after S /H and RD are
pull low, INT goes low, indicating that the conversion is
completed. Approximately 20 ns later the data appearing on
the TRI-STATE output pins will be valid. Note that data will
appear on these pins throughout the conversion, but until
INT goes low the data at the output pins will be the result of
the previous conversion.
2.0 REFERENCE CONSIDERATIONS
The ADC10461, ADC10462, and ADC10464 each have two
reference inputs. These inputs, V
REF+
and V
REF
, are fully
differential and define the zero to full-scale range of the input
signal. The reference inputs can be connected to span the
entire supply voltage range (V
REF
= 0V, V
REF+
= V
CC
) for
ratiometric applications, or they can be connected to differ-
ent voltages (as long as they are between ground and V
CC
)
when other input spans are required. Reducing the overall
V
span to less than 5V increases the sensitivity of the
converter (e.g., if V
= 2V, then 1 LSB = 1.953 mV). Note,
however, that linearity and offset errors become larger when
lower reference voltages are used. See the Typical Perfor-
mance Curves for more information. For this reason, refer-
ence voltages less than 2V are not recommended.
In most applications, V
REF
will simply be connected to
ground, but it is often useful to have an input span that is
offset from ground. This situation is easily accommodated by
the
reference
configuration
ADC10462, and ADC10464. V
can be connected to a
voltage other than ground as long as the voltage source
connected to this pin is capable of sinking the converter’s
reference current (12.5 mA Max
@
V
= 5V). If V
is
connected to a voltage other than ground, bypass it with
multiple capacitors.
Since the resistance between the two reference inputs can
be as low as 400
, the voltage source driving the reference
inputs should have low output impedance. Any noise on
either reference input is a potential cause of conversion
errors, so each of these pins must be supplied with a clean,
low noise voltage source. Each reference pin should be
bypassed with a 10 μF tantalum and a 0.1 μF ceramic.
used
in
the
ADC10461,
3.0 THE ANALOG INPUT
The ADC10461, ADC10462, and ADC10464 sample the
analog input voltage once every conversion cycle. When this
happens, the input is briefly connected to an impedance
approximately equal to 600
in series with 35 pF.
Short-duration current spikes can therefore be observed at
the analog input during normal operation. These spikes are
normal and do not degrade the converter’s performance.
Large source impedances can slow the charging of the
sampling capacitors and degrade conversion accuracy.
Therefore, only signal sources with output impedances less
than 500
should be used if rated accuracy is to be
achieved at the minimum sample time (250 ns maximum). If
the sampling time is increased, the source impedance can
be larger. If a signal source has a high output impedance, its
output should be buffered with an operational amplifier. The
operational amplifier’s output should be well-behaved when
driving a switched 35 pF/600
load. Any ringing or voltage
shifts at the op amp’s output during the sampling period can
result in conversion errors.
Correct conversion results will be obtained for input voltages
greater than GND 50 mV and less than V
+
+ 50 mV. Do not
allow the signal source to drive the analog input pin more
than 300 mV higher than AV
and DV
, or more than 300
mV lower than GND. If an analog input pin is forced beyond
these voltages, the current flowing through the pin should be
limited to 5 mA or less to avoid permanent damage to the IC.
The sum of all the overdrive currents into all pins must be
less than 20 mA. When the input signal is expected to extend
more than 300 mV beyond the power supply limits, some
sourt of protection scheme should be used.Asimple network
using diodes and resistors is shown in Figure 4
A
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| ADC10461CIWM | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10462CIWM | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10464CIWM | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10461CIWMX | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10462CIWMX | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC10461_06 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10461CIJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
| ADC10461CIWM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10461CIWM/NOPB | 功能描述:IC ADC 10BIT 600 NS 20-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| ADC10461CIWMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
發布緊急采購，3分鐘左右您將得到回復。