- 您現在的位置：買賣IC網 > PDF目錄378281 > ADC10462 (National Semiconductor Corporation) 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold(10位 600 ns帶輸入多路器和采樣/保持功能的A/D轉換器) PDF資料下載
參數資料
| 型號： | ADC10462 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold(10位 600 ns帶輸入多路器和采樣/保持功能的A/D轉換器) |
| 中文描述： | 10位600納秒的A / D輸入多路復用器和轉換器采樣/保持（10位600納秒帶輸入多路器和采樣/保持功能的的A / D轉換器） |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 329K |
| 代理商： | ADC10462 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
Connection Diagrams
Pin Descriptions
DV
CC
, AV
CC
These are the digital and analog positive sup-
ply voltage inputs. They should always be con-
nected to the same voltage source, but are
brought out separately to allow for separate
bypass capacitors. Each supply pin should be
bypassed with a 0.1 μF ceramic capacitor in
parallel with a 10 μF tantalum capacitor to
ground.
INT
This is the active low interrupt output. INT
goes low at the end of each conversion, and
returns to a high state following the rising edge
of RD .
S /H
This is the Sample/Hold control input. When
this pin is forced low (and CS is low), it causes
the analog input signal to be sampled and
initiates a new conversion.
RD
This is the active low Read control input.
When this RD and CS are low, any data
present in the output registers will be placed
on the data bus.
CS
This is the active low Chip Select control input.
When low, this pin enables the RD and S /H
pins.
S0, S1
On the multiple-input devices (ADC10462 and
ADC10464), these pins select the analog input
that will be connected to the A/D during the
conversion. The input is selected based on the
state of S0 and S1 when S /H makes its
High-to-Low transition (See the Timing Dia-
grams). The ADC10464 includes both S0 and
S1. The ADC10462 includes just S0, and the
ADC10461 includes neither.
V
REF
,
V
REF+
may be placed at any voltage between GND
and V
, but V
must be greater than
V
. An input voltage equal to V
pro-
duces an output code of 0, and an input volt-
age equal to (V
1 LSB) produces an
output code of 1023.
These are the reference voltage inputs. They
V
IN
, V
IN0
,
V
IN1
, V
IN2
,
V
IN3
These
ADC10461 has one input (V
), theADC10462
has two inputs (V
and V
IN1
), and the
ADC10464 has four inputs (V
, V
, V
and V
). The impedance of the source
should be less than 500
for best accuracy
and conversion speed. For accurate conver-
sions, no input pin (even one that is not se-
lected) should be driven more than 50 mV
above V
CC
or 50 mV below ground.
These are the power supply ground pins. The
ADC10461 has a single ground pin (GND),
and the ADC10462 and ADC10464 have
separate analog and digital ground pins
(AGND and DGND) for separate bypassing of
the analog and digital supplies. The ground
pins
should
be
connected
noise-free system ground. For the devices
with two ground pins, both pins should be
returned to the same potential.
These are the TRI-STATE output pins.
SPEED ADJ (ADC10462 and ADC10464 only). This pin is
normally left unconnected, but by connecting a
resistor between this pin and ground, the con-
version time can be reduced. See the Typical
Performance Curves and the table of Electri-
cal Characteristics.
are
the
analog
input
pins.
The
GND, AGND,
DGND
to
a
stable,
DB0–DB9
DS011108-10
Top View
DS011108-11
Top View
DS011108-12
Top View
A
www.national.com
2
相關PDF資料 |
PDF描述 |
|---|---|
| ADC10464 | 10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold(10位 600 ns帶輸入多路器和采樣/保持功能的A/D轉換器) |
| ADC104S051 | Switch-mode Multi-Chemistry Battery Charger with Peak Voltage Detection Termination 8-PDIP -20 to 70 |
| ADC104S101 | 4 Channel, 1 MSPS, 10-Bit A/D Converter |
| ADC104S021 | 4 Channel, 200 kSPS, 12-Bit A/D Converter |
| ADC1061CIWM | 10-Bit High-Speed レP-Compatible A/D Converter with Track/Hold Function |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC10462CIJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single-Ended Data Acquisition System |
| ADC10462CIWM | 功能描述:IC ADC 10BIT 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| ADC10462CIWM NOPB | 制造商:Texas Instruments 功能描述:ADC Single 800ksps 10-bit Parallel 24-Pin SOIC W |
| ADC10462CIWMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit 600 ns A/D Converter with Input Multiplexer and Sample/Hold |
| ADC10462CIWMX/NOPB | 制造商:Texas Instruments 功能描述:ADC Single 800ksps 10-bit Parallel 24-Pin SOIC W T/R |
發布緊急采購，3分鐘左右您將得到回復。