- 您現在的位置：買賣IC網 > PDF目錄378281 > ADC104S021 (National Semiconductor Corporation) 4 Channel, 200 kSPS, 12-Bit A/D Converter PDF資料下載
參數資料
| 型號： | ADC104S021 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 4 Channel, 200 kSPS, 12-Bit A/D Converter |
| 中文描述： | 4通道，200 kSPS的，12位A / D轉換器 |
| 文件頁數： | 7/19頁 |
| 文件大?。?/td> | 964K |
| 代理商： | ADC104S021 |
Specification Definitions
ACQUISITION TIME
is the time required to acquire the input
voltage. That is, it is time required for the hold capacitor to
charge up to the input voltage.
APERTURE DELAY
is the time between the fourth falling
SCLK edge of a conversion and the time when the input
signal is acquired or held for conversion.
CONVERSION TIME
is the time required, after the input
voltage is acquired, for the ADC to convert the input voltage
to a digital word.
CROSSTALK
is the coupling of energy from one channel
into the other channel, or the amount of signal energy from
one analog input that appears at the measured analog input.
DIFFERENTIAL NON-LINEARITY (DNL)
is the measure of
the maximum deviation from the ideal step size of 1 LSB.
DUTY CYCLE
is the ratio of the time that a repetitive digital
waveform is high to the total time of one period. The speci-
fication here refers to the SCLK.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS)
is another method of specifying Signal-to-Noise and
Distortion
or
SINAD.
(SINAD 1.76) / 6.02 and says that the converter is equiva-
lent to a perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH
is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its low frequency value for a full scale input.
GAIN ERROR
is the deviation of the last code transition
(111...110) to (111...111) from the ideal (V
REF
1.5 LSB),
after adjusting for offset error.
INTEGRAL NON-LINEARITY (INL)
is a measure of the
deviation of each individual code from a line drawn from
negative full scale (
1
2
LSB below the first code transition)
through positive full scale (
1
2
LSB above the last code
transition). The deviation of any given code from this straight
line is measured from the center of that code value.
INTERMODULATION DISTORTION (IMD)
is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to theADC input at the same time.
It is defined as the ratio of the power in the second and third
order intermodulation products to the sum of the power in
both of the original frequencies. IMD is usually expressed in
dB.
ENOB
is
defined
as
MISSING CODES
are those output codes that will never
appear at the ADC outputs. The ADC104S101 is guaranteed
not to have any missing codes.
OFFSET ERROR
is the deviation of the first code transition
(000...000) to (000...001) from the ideal (i.e. GND + 0.5
LSB).
SIGNAL TO NOISE RATIO (SNR)
is the ratio, expressed in
dB, of the rms value of the input signal to the rms value of the
sum of all other spectral components below one-half the
sampling frequency, not including harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD)
Is the ratio, expressed in dB, of the rms value of the input
signal to the rms value of all of the other spectral compo-
nents below half the clock frequency, including harmonics
but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
is the differ-
ence, expressed in dB, between the rms values of the input
signal and the peak spurious signal where a spurious signal
is any signal present in the output spectrum that is not
present at the input, excluding d.c.
TOTAL HARMONIC DISTORTION (THD)
is the ratio, ex-
pressed in dB or dBc, of the rms total of the first five
harmonic components at the output to the rms level of the
input signal frequency as seen at the output. THD is calcu-
lated as
where A
f1
is the RMS power of the input frequency at the
output and A
through A
f6
are the RMS power in the first 5
harmonic frequencies.
THROUGHPUT TIME
is the minimum time required between
the start of two successive conversion. It is the acquisition
time plus the conversion time. In the case of the
ADC104S101, this is 16 SCLK periods.
A
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| ADC1061CIWM | 10-Bit High-Speed レP-Compatible A/D Converter with Track/Hold Function |
| ADC1061 | 10-Bit High-Speed レP-Compatible A/D Converter with Track/Hold Function |
| ADC1061CIN | Switch-mode Multi-Chemistry Battery Charger with Peak Voltage Detection Termination 8-SOIC -20 to 70 |
| ADC10662CIWM | RES 12-OHM 5% 0.25W 200PPM THK-FILM SMD-1206 TR-7-PA |
| ADC10662 | 10-Bit 360 ns A/D Converter with Input Multiplexer and Sample/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC104S021CIMM | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC104S021CIMM/NOPB | 功能描述:模數轉換器 - ADC 4CH,50KSPS-200KSPS, 10B ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC104S021CIMMX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC104S021CIMMX/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC104S021EVAL | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:4 Channel, 200 kSPS, 10-Bit A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。