參數資料
型號: ADC1061CIWM
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: ADC
英文描述: 10-Bit High-Speed レP-Compatible A/D Converter with Track/Hold Function
中文描述: 1-CH 10-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDSO20
封裝: SOP-20
文件頁數: 9/11頁
文件大小: 320K
代理商: ADC1061CIWM
4.0 Inherent Sample-and-Hold
(Continued)
The ADC1061 can perform accurate conversions of input
signals at frequencies from DC to greater than 160 kHz with-
out the need for external sampling circuitry.
5.0 Power Supply Considerations
The ADC1061 is designed to operate from a +5V (nominal)
power supply. There are two supply pins, AV
and DV
.
These pins allow separate external bypass capacitors for the
analog and digital portions of the circuit. To guarantee accu-
rate conversions, the two supply pins should be connected
to the same voltage source, and each should be bypassed
with a 0.1 μF ceramic capacitor in parallel with a 10 μF tan-
talum capacitor. Depending on the circuit board layout and
other system considerations, more bypassing may be neces-
sary.
It is important to ensure that none of the ADC1061’s input or
output pins are ever driven to a voltage more than 300 mV
above AV
and DV
, or more than 300 mV below GND. If
these voltage limits are exceeded, the overdrive current into
or out of any pin on the ADC1061 must be limited to less
than 5 mA, and no more than 20 mA of overdrive current (all
overdriven pins combined) should flow. In systems with mul-
tiple power supplies, this may require careful attention to
power supply sequencing. The ADC1061’s power supply
pins should be at the proper voltage before signals are ap-
plied to any of the other pins.
6.0 Layout and Grounding
In order to ensure fast, accurate conversions from the
ADC1061, it is necessary to use appropriate circuit board
layout techniques. The analog ground return path should be
low-impedance and free of noise from other parts of the sys-
tem. Noise from digital circuitry can be especially trouble-
some, so digital grounds should always be separate from
analog grounds. For best performance, separate ground
planes should be provided for the digital and analog parts of
the system.
All bypass capacitors should be located as close to the con-
verter as possible and should connect to the converter and
to ground with short traces. The analog input should be iso-
lated from noisy signal traces to avoid having spurious sig-
nals couple to the input. Any external component (e.g., a fil-
ter capacitor) connected across the converter’s input should
be connected to a very clean ground return point. Grounding
the component at the wrong point will result in reduced con-
version accuracy.
www.national.com
9
相關PDF資料
PDF描述
ADC1061 10-Bit High-Speed レP-Compatible A/D Converter with Track/Hold Function
ADC1061CIN Switch-mode Multi-Chemistry Battery Charger with Peak Voltage Detection Termination 8-SOIC -20 to 70
ADC10662CIWM RES 12-OHM 5% 0.25W 200PPM THK-FILM SMD-1206 TR-7-PA
ADC10662 10-Bit 360 ns A/D Converter with Input Multiplexer and Sample/Hold
ADC10664 Switch-mode Multi-Chemistry Battery Charger with Peak Voltage Detection Termination 8-SOIC -20 to 70
相關代理商/技術參數
參數描述
ADC1061CIWM/NOPB 制造商:Texas Instruments 功能描述:ADC Single Semiflash 556ksps 10-bit Parallel 20-Pin SOIC W
ADC1061CIWMX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter, 10-Bit
ADC1061CIWMX/NOPB 制造商:Texas Instruments 功能描述:ADC Single Semiflash 556ksps 10-bit Parallel 20-Pin SOIC W T/R
ADC10662 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit 360 ns A/D Converter with Input Multiplexer and Sample/Hold
ADC10662CIJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single-Ended Data Acquisition System