參數資料
型號： ADC12062
廠商： National Semiconductor Corporation
英文描述： Single-Wire Advanced Battery Monitor IC for Cellular and PDA Applications 8-TSSOP -20 to 70
中文描述： 12位，1兆赫，75毫瓦的A / D轉換器
文件頁數： 12/20頁
文件大?。?/td> 355K
代理商： ADC12062
Applications Information
(Continued)
TL/H/11490–16
FIGURE 6. ADC Control Logic
2.0 THE ANALOG INPUT
The analog input of the ADC12062 can be modeled as two
small resistances in series with the capacitance of the input
hold capacitor (C
IN
), as shown in Figure 7. The S/H switch
is closed during the Sample period, and open during Hold.
The source has to charge C
IN
to the input voltage within the
sample period. Note that the source impedance of the input
voltage (R
SOURCE
) has a direct effect on the time it takes to
charge C
IN
. If R
SOURCE
is too large, the voltage across C
IN
will not settle to within 0.5 LSBs of V
SOURCE
before the
conversion begins, and the conversion results will be incor-
rect. From a dynamic performance viewpoint, the combina-
tion of R
SOURCE
, R
MUX
, R
SW
, and C
IN
form a low pass
filter. Minimizing R
SOURCE
will increase the frequency re-
sponse of the input stage of the converter.
Typical values for the components shown in Figure 7 are:
R
MUX
e
100
X
, R
SW
e
100
X
, and C
IN
e
25 pF. The set-
tling time to n bits is:
t
SETTLE
e
(R
SOURCE
a
R
MUX
a
R
SW
)
*
C
IN
*
n
*
ln (2).
The bandwidth of the input circuit is:
f
b
3dB
e
1/(2
*
3.14
*
(R
SOURCE
a
R
MUX
a
R
SW
)
*
C
IN
)
For maximum performance, the impedance of the source
driving the ADC12062 should be made as small as possible.
A source impedance of 100
X
or less is recommended. A
plot of dynamic performance vs. source impedance is given
in the Typical Performance Characteristics section.
If the signal source has a high output impedance, its output
should be buffered with an operational amplifier capable of
driving a switched 25 pF/100
X
load. Any ringing or instabili-
ties at the op amp’s output during the sampling period can
result in conversion errors. The LM6361 high speed op amp
is a good choice for this application due to its speed and its
ability to drive large capacitive loads. Figure 8 shows the
LM6361 driving the ADC IN input of an ADC12062. The
100 pF capacitor at the input of the converter absorbs some
of the high frequency transients generated by the S/H
switching, reducing the op amp transient response require-
ments. The 100 pF capacitor should only be used with high
speed op amps that are unconditionally stable driving ca-
pacitive loads.
TL/H/11490–17
FIGURE 7. Simplified ADC12062 Input Stage
12
相關PDF資料
PDF描述
ADC12062BIV 12-Bit, 1 MHz, 75 mW A/D Converter
ADC12062CIV 12-Bit, 1 MHz, 75 mW A/D Converter
ADC12062BIVF 12-Bit, 1 MHz, 75 mW A/D Converter
ADC12081CIVT 12-Bit, 5 MHz Self-Calibrating, Pipelined A/D Converter
ADC12081 12-Bit, 5 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold(12位5 MHz可自行校對的管線式帶內部采樣和保持功能A/D轉換器)
相關代理商/技術參數
參數描述
ADC12062BIV 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 1 MHz, 75 mW A/D Converter
ADC12062BIVF 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 1 MHz, 75 mW A/D Converter
ADC12062CIV 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 1 MHz, 75 mW A/D Converter
ADC12062CIVF 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 1 MHz, 75 mW A/D Converter
ADC12062EVAL 功能描述:BOARD EVALUATION FOR ADC12062 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*