- 您現在的位置：買賣IC網 > PDF目錄378283 > ADC12181CIVT (NATIONAL SEMICONDUCTOR CORP) 12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold PDF資料下載
參數資料
| 型號： | ADC12181CIVT |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | ADC |
| 英文描述： | 12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold |
| 中文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32 |
| 封裝： | TQFP-32 |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 322K |
| 代理商： | ADC12181CIVT |
AC Electrical Characteristics
(Continued)
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2:
All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified.
Note 3:
When the input voltage at any pin exceeds the power supplies (that is, V
IN
<
AGND, or V
IN
>
V
A
, V
D
or V
D
I/O), the current at that pin should be limited
to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to
two.
Note 4:
The absolute maximum junction temperatures (T
J
max) for this device is 150C. The maximum allowable power consumption is dictated by T
J
max, the
junction-to-ambient thermal resistance (
θ
JA
), and the ambient temperature, (T
A
), and can be calculated using the formula P
D
MAX = (T
J
max - T
A
)/
θ
JA
. In the 32-pin
TQFP,
θ
JA
is 74C/W, so P
D
MAX = 1,689 mW at 25C and 1,013 mW at the maximum operating ambient temperature of 75C. Note that the power consumption
of this device under normal operation will typically be about 255 mW (typical power consumption + 20 mW TTL output loading). The values for maximum power
consumption listed above will be reached only when the ADC12181 is operated in a severe fault condition (e.g. when input or output pins are driven beyond the
power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.
Note 5:
Human body model is 100 pF capacitor discharged through a 1.5k
resistor. Machine model is 220 pf discharged through ZERO Ohms.
Note 6:
See AN450, "Surface Mounting Methods and Their Effect on Product Reliability", or the section entitled "Surface Mount" found in any post 1986 National
Semiconductor Linear Data Book, for other methods of soldering surface mount devices.
Note 7:
The inputs are protected as shown below. Input voltage magnitudes up to 5V above V
A
or to 5V below GND will not damage this device, provided current
is limited per Note 3. However, errors in the A/D conversion can occur if the input goes above V
A
or below GND by more than 100 mV. As an example, if V
A
is 4.75V,
the full-scale input voltage must be
≤
4.85V to ensure accurate conversions.
10103908
Note 8:
To guarantee accuracy, it is required that |V
A
- V
D
|
≤
100mV and separate bypassed capacitors are used at each power supply pin.
Note 9:
With the test condition for V
REF
= +2.0V, the 12-bit LSB is 488μV.
Note 10:
Typical figures are at T
A
= T
J
= 25C, and represent most likely parametric norms.
Note 11:
Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 12:
Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive full-scall and
zero.
Note 13:
Timing specifications are tested at the TTL logic levels, V
IL
= 0.4V for a falling edge and V
IH
= 2.4V for a rising edge. TRI-STATE output voltage is forced
to 1.4V.
Note 14:
Optimum SNR performance will be obtained by keeping the reference input in the 1.8V to 2.2V range. The LM4041CIM3-ADJ (SOT-23 package), the
LM4041CIZ-ADJ (TO-92 package), or the LM4041CIM-ADJ (SOT-8 package) bandgap voltage reference is recommended for this application.
A
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| ADC12181EVAL | 12-Bit, 5 MHz Self-Calibrating, Pipelined A/D Converter |
| ADC12191CIVT | 12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold |
| ADC12191 | 12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold(12位10 MHz可自行校對的管線式帶內部采樣和保持功能A/D轉換器) |
| ADC121S625 | 12-Bit, 50 ksps to 200 ksps, Differential Input, Micro Power Sampling A/D Converter |
| ADC121S625CIMM | 12-Bit, 50 ksps to 200 ksps, Differential Input, Micro Power Sampling A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC12181EVAL | 功能描述:BOARD EVALUATION FOR ADC12181 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| ADC12191 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold |
| ADC12191CIVT | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold |
| ADC121C021 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:I2C-Compatible, 12-Bit Analog-to-Digital Converter (ADC) with Alert Function |
| ADC121C021CIMK | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。