- 您現在的位置：買賣IC網 > PDF目錄378284 > ADC128S022EVAL (National Semiconductor Corporation) 8-Channel, 50 kSPS to 200 kSPS, 12-Bit A/D Converter PDF資料下載
參數資料
| 型號： | ADC128S022EVAL |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 8-Channel, 50 kSPS to 200 kSPS, 12-Bit A/D Converter |
| 中文描述： | 8通道，50 kSPS的200 kSPS的，12位A / D轉換器 |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 848K |
| 代理商： | ADC128S022EVAL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁
1.0 Functional Description
(Continued)
neously and the ADC enters track mode. While there is no
timing restriction with respect to the falling edges of CS and
SCLK, see
Figure 3
for setup and hold time requirements for
the falling edge of CS with respect to the rising edge of
SCLK.
During each conversion, data is clocked into a control reg-
ister through the DIN pin on the first 8 rising edges of SCLK
after the fall of CS. The control register is loaded with data
indicating the input channel to be converted on the subse-
quent conversion (see
Tables 1, 2, 3
).
The user does not need to incorporate a power-up delay or
dummy conversions as the ADC128S022 is able to acquire
the input signal to full resolution in the first conversion im-
mediately following power-up. The first conversion result
after power-up will be that of IN0.
TABLE 1. Control Register Bits
Bit 7 (MSB)
DONTC
Bit 6
DONTC
Bit 5
ADD2
Bit 4
ADD1
Bit 3
ADD0
Bit 2
DONTC
Bit 1
DONTC
Bit 0
DONTC
TABLE 2. Control Register Bit Descriptions
Bit #:
7, 6, 2, 1, 0
5
4
3
Symbol:
DONTC
ADD2
ADD1
ADD0
Description
Don’t care. The values of these bits do not affect the device.
These three bits determine which input channel will be sampled and
converted at the next conversion cycle. The mapping between codes and
channels is shown in
Table 3
.
TABLE 3. Input Channel Selection
ADD2
0
0
0
0
1
1
1
1
ADD1
0
0
1
1
0
0
1
1
ADD0
0
1
0
1
0
1
0
1
Input Channel
IN0 (Default)
IN1
IN2
IN3
IN4
IN5
IN6
IN7
1.3 ADC128S022 TRANSFER FUNCTION
The output format of the ADC128S022 is straight binary.
Code transitions occur midway between successive integer
LSB values. The LSB width for the ADC128S022 is V
/
4096. The ideal transfer characteristic is shown in
Figure 6
.
The transition from an output code of 0000 0000 0000 to a
code of 0000 0000 0001 is at 1/2 LSB, or a voltage of V
A
/
8192. Other code transitions occur at steps of one LSB.
1.4 ANALOG INPUTS
An equivalent circuit for one of the ADC128S022’s input
channels is shown in
Figure 7
. Diodes D1 and D2 provide
ESD protection for the analog inputs. The operating range
for the analog inputs is 0 V to V
A
. Going beyond this range
will cause the ESD diodes to conduct and result in erratic
operation.
The capacitor C1 in
Figure 7
has a typical value of 3 pF and
is mainly the package pin capacitance. Resistor R1 is the on
resistance of the multiplexer and track / hold switch and is
typically 500 ohms. Capacitor C2 is the ADC128S022 sam-
pling capacitor, and is typically 30 pF. The ADC128S022 will
deliver best performance when driven by a low-impedance
source (less than 100 ohms). This is especially important
when using the ADC128S022 to sample dynamic signals.
Also important when sampling dynamic signals is a band-
pass or low-pass filter which reduces harmonics and noise in
the input. These filters are often referred to as anti-aliasing
filters.
1.5 DIGITAL INPUTS AND OUTPUTS
TheADC128S022’s digital inputs (SCLK, CS, and DIN) have
an operating range of -0.3 V to V
A
. They are not prone to
latch-up and may be asserted before the digital supply (V
D
)
without any risk. The digital output (DOUT) operating range
is controlled by V
D
. The output high voltage is V
D
- 0.5V
(min) while the output low voltage is 0.4V (max).
20162711
FIGURE 6. Ideal Transfer Characteristic
20162714
FIGURE 7. Equivalent Input Circuit
A
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| ADC12H030 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold(可自行校對12位串行輸入/輸出帶MUX，采樣/保持功能A/D轉換器) |
| ADC12030 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| ADC12032 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| ADC12034 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| ADC12038 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC128S022EVAL/NOPB | 功能描述:數據轉換 IC 開發工具 ADC128S022 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADC128S052 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Channel, 200 kSPS to 500 kSPS, 12-Bit A/D Converter |
| ADC128S052CIMT | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC128S052CIMT/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC128S052CIMTX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。