- 您現在的位置：買賣IC網 > PDF目錄362131 > ADC700KH 16-Bit Resolution With Microprocessor Interface A/D CONVERTER PDF資料下載
參數資料
| 型號： | ADC700KH |
| 英文描述： | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| 中文描述： | 16位分辨率，微處理器接口的A / D轉換器 |
| 文件頁數： | 6/12頁 |
| 文件大小： | 148K |
| 代理商： | ADC700KH |
6
ADC700
TWO’S COMPLEMENT DATA CODE
BTCEN (pin 23) is a logic function that implements the
Binary Two’s Complement output code for bipolar (+ and –)
analog input signal operation. This feature is compatible
with twos complement arithmetic in microprocessor math
algorithms.
INTERNAL CLOCK
The ADC700 has a self-contained clock to sequence the
A/D logic. The clock is not available externally. An external
16-pulse strobe (pin 14) is brought out to clock serial data
only. Use of ADC700 with external clock is not possible.
INTERNAL VOLTAGE REFERENCE
The ADC700 has an internal low-noise buried-zener voltage
reference. The reference circuit has been drift compensated
over the MIL temperature range using a laser trim algorithm.
The reference voltage is not available externally.
DISCUSSION
OF SPECIFICATIONS
BASIC DEFINITIONS
Refer to Figure 3 for an illustration of A/D converter
terminology and to Table II in the Calibration section.
Full Scale Range, FSR
The nominal range of the A/D converter. For ADC700, the
FSR is 20V for the 0V to +20V and the –10V to +10V input
ranges or 10V for the 0V to +10V and –5V to +5V input
ranges.
Least Significant Bit, LSB
The smallest analog input change resolved by the A/D
converter. For an A/D converter with N bits output, the input
value of the LSB is FSR(2
–N
).
FIGURE 1. Load Circuits for Access Time.
DBN
3k
C
L
DGND
DBN
3k
C
L
DGND
5V
A) High-Z to V
OH
(t
3
)
and V
OL
(t
6
).
to V
OH
B) High-Z to V
OL
(t
3
)
and V
OH
(t
6
).
to V
OL
Most Significant Bit, MSB
That binary digit that has the greatest value or weight. The
MSB weight is FSR/2.
Resolution
An N-bit binary-coded A/D converter resolves the analog
input into 2
N
values represented by the 2
N
digital output
codes.
ACCURACY
Linearity Error, Integral Linearity Error (ILE)
Linearity Error is defined as the deviation of actual analog
input values from the ideal values about a straight line drawn
through the code mid-points near positive full scale (at +V
FS
–1LSB) and at Zero input (at 1/2LSB below the first code
transition, i.e. at Zero) or, in the case of bipolar operation,
near minus full scale (at 1/2LSB below the first code
transition, i.e. at –V
FS
). Despite the definition, however,
code transitions are easier to measure than code midpoints.
Therefore linearity is measured as the deviation of the
analog input values from a line drawn between the first and
last code transitions. Linearity Error specifications are ex-
pressed in % of Full Scale Range (FSR). ADC700KH ILE
is
±
0.003% of FSR which is 1/2 LSB at 14-bits.
Differential Linearity Error (DLE), No Missing Codes
Differential Linearity Error is defined as the deviation in
code width from the ideal value of 1LSB. If the DLE is
greater than –1LSB anywhere along the range, the A/D will
have at least one missing code. ADC700KH is specified to
have a DLE of
±
0.006% of FSR, which is
±
1LSB at 14 bits.
ADC700KH is specified to have
no missing codes
at the 14-
bit level over specified temperature ranges.
Gain Error
The deviation from the ideal magnitude of the input span
between the first code midpoint (at –V
FS
+ 1/2LSB, for
bipolar operation; at Zero for unipolar operation) to the last
code midpoint (V
FS
–1LSB). As with the linearity error
DBN
3k
DGND
DBN
3k
10pF
DGND
5V
B) V
OL
to High-Z.
10pF
A) V
OH
to High-Z.
FIGURE 2. Load Circuits for Output Float Delay.
FIGURE 3. Transfer Characteristic Terminology.
Offset Error
Shifts The Line
Gain
Error
Rotates
The
Line
FFF
H
FFE
H
FFD
H
802
H
801
H
800
H
7FF
H
7FE
H
002
H
001
H
000
H
(Bipolar
Zero
Transition)
1/2LSB
Zero
(–Full
Scale)
1/2LSB
3/2LSB
+Full-Scale
Calibration
Transition
+Full
Scale
Zero
(–Full-Scale
Calibration
Transition)
Midscale
(Bipolar Zero)
Analog Input
相關PDF資料 |
PDF描述 |
|---|---|
| ADC700RH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700SH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700AH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700BH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700JH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC700RH | 制造商:BB 制造商全稱:BB 功能描述:16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700SH | 制造商:BB 制造商全稱:BB 功能描述:16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC701 | 制造商:BB 制造商全稱:BB 功能描述:16-Bit 512kHz SAMPLING A/D CONVERTER SYSTEM |
| ADC701 WAF | 制造商:Texas Instruments 功能描述: |
| ADC701/SHC702 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADC701. SHC702 - DISCONTINUED PRODUCT. No longer recommended for new design. |
發布緊急采購，3分鐘左右您將得到回復。