- 您現在的位置：買賣IC網 > PDF目錄362131 > ADC700RH 16-Bit Resolution With Microprocessor Interface A/D CONVERTER PDF資料下載
參數資料
| 型號： | ADC700RH |
| 英文描述： | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| 中文描述： | 16位分辨率，微處理器接口的A / D轉換器 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 148K |
| 代理商： | ADC700RH |
5
ADC700
PIN CONFIGURATION
DESCRIPTION
AND OPERATING FEATURES
The ADC700 is a 16-bit resolution successive approxima-
tion A/D converter. Parallel digital data as well as serial data
is available. Several features have been included in the
ADC700 making it easier to interface with microprocessors
and/or serial data systems. Several analog input ranges are
available.
Some of the key operating features are described here. More
detail is given in later sections of the data sheet. Refer to the
block diagram above.
RESET
The ADC700 has a Reset input that must be asserted upon
power-up or after a power interruption. This initializes the
SAR, the output buffer register and Data Ready flag. Since
microprocessor systems already use a power-on reset circuit,
the same system reset signal can be used to initialize the
ADC700.
PARALLEL DATA
The parallel data output is available through an 8-bit port
with 3-state output drivers. High byte and low byte are
selected by HBEN (pin 10).
A buffer/latch is included between the successive approxi-
mation register (SAR) and the 3-state drivers. This feature
permits more flexible interface timing than is possible from
most successive approximation converters.
The “old” word can be read during the next conversion. A
Data Ready flag (pin 12) is asserted when a “new” word is
in the buffer register. The Data Ready flag goes low (“0”)
when the most significant byte (high byte) is read. If the
“old” word is not read, or if only the least significant byte
(low byte) is read, Data Ready is not reset. The next
conversion output will overwrite the data latch when the
conversion is complete. The Data Ready flag remains high.
Refer to timing diagrams in the Specifications section.
SERIAL DATA
Sixteen-bit serial data output is available (pin 11) along with
a serial output strobe (pin 14). This serial data strobe is not
the internal SAR clock but is a special strobe for serial data
consisting of 16 negative-going edges (during conversion)
occurring about 200ns after each serial data bit is valid. This
feature eases the interface to shift registers or through opto-
couplers for applications requiring galvanic isolation.
STATUS
The familiar Status (or Busy) flag, present in successive
approximation A/D converters, is available (pin 13) and
indicates that a conversion is in progress. Status is valid
110ns after assertion of the convert command (WR low).
Status cannot be used as a sample-hold control because there
is not enough time for the sample-hold to settle to the
required error band before the ADC700 makes its first
conversion decision.
CHIP SELECT
CS (pin 9) selects the ADC700. No other functions can be
implemented unless CS is asserted. WR (pin 7) is the start-
of-conversion strobe. RD strobes each output data byte,
selected by HBEN (pin 10), to the 3-state drivers.
LSB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
16-Bit
D/A
Converter
Successive
Approximation
Register
20V Range
10V Range
Analog Common
Digital Common
V
BTCEN
DB15/DB7
DB14/DB6
DB13/DB5
DB12/DB4
DB11/DB3
DB10/DB2
DB9/DB1
DB8/DB0
DD
Comparator In
Bipolar Offset
Gain Adjust
Reset
WR
RD
CS
HBEN
Serial Data
Data Ready
Status
Serial Data Strobe
CC
+V
CC
–V
All internal control lines not shown. Refer to Figures 4 and 5 for Offset and Gain Adjust connections.
Data
Latch
3-State
Drivers
MSB LSB
Voltage
Reference
Clock and Clock Logic
5k
5k
MSB
Control Logic
相關PDF資料 |
PDF描述 |
|---|---|
| ADC700SH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700AH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700BH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC700JH | 16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC701 | 16-Bit 512kHz SAMPLING A/D CONVERTER SYSTEM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC700SH | 制造商:BB 制造商全稱:BB 功能描述:16-Bit Resolution With Microprocessor Interface A/D CONVERTER |
| ADC701 | 制造商:BB 制造商全稱:BB 功能描述:16-Bit 512kHz SAMPLING A/D CONVERTER SYSTEM |
| ADC701 WAF | 制造商:Texas Instruments 功能描述: |
| ADC701/SHC702 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADC701. SHC702 - DISCONTINUED PRODUCT. No longer recommended for new design. |
| ADC70726302 | 制造商:LG Corporation 功能描述:Door Assembly,Freezer |
發布緊急采購，3分鐘左右您將得到回復。