- 您現在的位置：買賣IC網 > PDF目錄1898 > ADM3053BRWZ-REEL7 (Analog Devices Inc)IC TXRX ISOLATED CAN 20SOIC PDF資料下載
參數資料
| 型號： | ADM3053BRWZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX ISOLATED CAN 20SOIC |
| 產品培訓模塊： | iCoupler Digital Isolater Technology |
| 標準包裝： | 400 |
| 系列： | IsoPower®, iCoupler® |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 3.3V，5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC W |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Data Sheet
ADM3053
Rev. B | Page 13 of 20
CIRCUIT DESCRIPTION
CAN TRANSCEIVER OPERATION
A CAN bus has two states called dominant and recessive. A
dominant state is present on the bus when the differential
voltage between CANH and CANL is greater than 0.9 V. A
recessive state is present on the bus when the differential voltage
between CANH and CANL is less than 0.5 V. During a dominant
bus state, the CANH pin is high, and the CANL pin is low.
During a recessive bus state, both the CANH and CANL pins
are in the high impedance state.
Pin 18 (RS) allows two different modes of operation to be
selected: high-speed and slope control. For high-speed
operation, the transmitter output transistors are simply
switched on and off as fast as possible. In this mode, no
measures are taken to limit the rise and fall slopes. A shielded
cable is recommended to avoid EMI problems. High-speed
mode is selected by connecting Pin 18 to ground.
Slope control mode allows the use of an unshielded twisted pair
or a parallel pair of wires as bus lines. To reduce EMI, the rise
and fall slopes should be limited. The rise and fall slopes can be
programmed with a resistor connected from Pin 18 to ground.
The slope is proportional to the current output at Pin 18.
SIGNAL ISOLATION
The ADM3053 signal isolation is implemented on the logic side of
the interface. The part achieves signal isolation by having a
digital isolation section and a transceiver section (see Figure 1).
Data applied to the TxD pin referenced to logic ground (GND1)
are coupled across an isolation barrier to appear at the transceiver
section referenced to isolated ground (GND2). Similarly, the
single-ended receiver output signal, referenced to isolated
ground in the transceiver section, is coupled across the isolation
barrier to appear at the RxD pin referenced to logic ground
(GND1). The signal isolation is powered by the VIO pin and
allows the digital interface to 3.3 V or 5 V logic.
POWER ISOLATION
The ADM3053 power isolation is implemented using an
iso
Power integrated isolated dc-to-dc converter. The dc-to-dc
converter section of the ADM3053 works on principles that are
common to most modern power supplies. It is a secondary side
controller architecture with isolated pulse-width modulation
(PWM) feedback. VCC power is supplied to an oscillating circuit
that switches current into a chip-scale air core transformer.
Power transferred to the secondary side is rectified and regulated to
5 V. The secondary (VISO) side controller regulates the output by
creating a PWM control signal that is sent to the primary (VCC)
side by a dedicated iCoupler data channel. The PWM modulates
the oscillator circuit to control the power being sent to the
secondary side. Feedback allows for significantly higher power
and efficiency.
TRUTH TABLES
The truth tables in this section use the abbreviations found in
Table 9. Truth Table Abbreviations
Letter
Description
H
High level
L
Low level
X
Don’t care
Z
High impedance (off)
I
Indeterminate
NC
Not connected
Table 10. Transmitting
Supply Status
Input
Outputs
VIO
VCC
TxD
Bus State
CANH
CANL
On
L
Dominant
H
L
On
H
Recessive
Z
On
Floating
Recessive
Z
Off
On
X
Recessive
Z
On
Off
L
Indeterminate
I
Table 11. Receiving
Supply Status
Inputs
Output
VIO
VCC
VID = CANH CANL
Bus State
RxD
On
≥ 0.9 V
Dominant
L
On
≤ 0.5 V
Recessive
H
On
0.5 V < VID < 0.9 V
I
On
Inputs open
Recessive
H
Off
On
I
On
Off
H
1
X = don’t care.
THERMAL SHUTDOWN
The ADM3053 contains thermal shutdown circuitry that protects
the part from excessive power dissipation during fault conditions.
Shorting the driver outputs to a low impedance source can
result in high driver currents. The thermal sensing circuitry
detects the increase in die temperature under this condition and
disables the driver outputs. This circuitry is designed to disable
the driver outputs when a die temperature of 150°C is reached.
As the device cools, the drivers are reenabled at a temperature of
140°C.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
The digital signals transmit across the isolation barrier using
i
Coupler technology. This technique uses chip-scale transformer
windings to couple the digital signals magnetically from one
side of the barrier to the other. Digital inputs are encoded into
waveforms that are capable of exciting the primary transformer
相關PDF資料 |
PDF描述 |
|---|---|
| ADM3054BRWZ-RL7 | IC TXRX CAN HS 16SOIC |
| ADM3071EARZ | IC TXRX RS-485 3.3V FD 8-SOIC |
| ADM3101EARQZ-REEL | IC TXRX RS-232 3.3V 15KV 16QSOP |
| ADM3232EARWZ | IC RCVR/LINEDRIVER RS232 16SOIC |
| ADM3251EARWZ | IC TXRX RS232 ISOLATED 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM3054 | 制造商:Analog Devices 功能描述:IC CAN TRANSCEIVER 1MBPS 16SOIC 制造商:Analog Devices 功能描述:IC, CAN, TRANSCEIVER, 1MBPS, 16SOIC 制造商:Analog Devices 功能描述:IC, CAN, TRANSCEIVER, 1MBPS, 16SOIC; Interface Type:CAN; No. of TX Buffers:1; No. of RX Buffers:1; Supply Voltage Min:3V; Supply Voltage Max:5.5V; Digital IC Case Style:SOIC; No. of Pins:16; Operating Temperature Min:-40C; Operating;RoHS Compliant: Yes |
| ADM3054BRWZ | 功能描述:IC TRANSCEIVER CAN 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:* 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| ADM3054BRWZ | 制造商:Analog Devices 功能描述:IC Interface Type:- No. of TX Buffers |
| ADM3054BRWZ-RL7 | 功能描述:IC TXRX CAN HS 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:* 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| ADM3054WBRWZ-RL7 | 功能描述:CAN Digital Isolator 5000Vrms 3 Channel 1Mbps 25kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包裝:剪切帶（CT） 零件狀態:有效 技術:磁耦合 類型:CAN 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:1/2 通道類型:單向 電壓 - 隔離:5000Vrms 共模瞬態抗擾度（最小值）:25kV/μs 數據速率:1Mbps 傳播延遲 tpLH / tpHL（最大值）:- 脈寬失真（最大）:- 上升/下降時間（典型值）:- 電壓 - 電源:3.3V，5V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:16-SOIC 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。