- 您現在的位置：買賣IC網 > PDF目錄2140 > ADMP441ACEZ-RL (Analog Devices Inc)MIC MEMS OMNI-DIR DIGITAL 9-LGA PDF資料下載
參數資料
| 型號： | ADMP441ACEZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | MIC MEMS OMNI-DIR DIGITAL 9-LGA |
| 標準包裝： | 1 |
| 系列： | ADMP441 |
| 類型： | MEMS（硅） |
| 輸出類型： | 數字、I²S |
| 方向： | 全向 |
| 頻率范圍： | 60Hz ~ 15kHz |
| 靈敏度： | -26dB ±3dB |
| 信噪比： | 61dB |
| 電壓 - 額定： | 1.8 ~ 3.3V |
| 電流 - 電源： | 1.6mA |
| 端口位置： | 底部 |
| 密封等級： | 無 |
| 端子： | 表面貼裝型 |
| 尺寸/尺寸： | 4.72mm L x 3.76mm W |
| 高度（最大）： | 1.05mm |
| 形狀： | 矩形 |
| 包裝： | 標準包裝 |
| 其它名稱： | ADMP441ACEZ-RLDKR |
Data Sheet
ADMP441
Rev. B | Page 11 of 16
APPLICATIONS INFORMATION
POWER SUPPLY DECOUPLING
For best performance and to avoid potential parasitic artifacts,
placing a 0.1 F ceramic type X7R or better capacitor between
Pin 7 (VDD) and ground is strongly recommended. The
capacitor should be placed as close to Pin 7 as possible.
The connections to each side of the capacitor should be as short
as possible, and the trace should stay on a single layer with no
vias. For maximum effectiveness, locate the capacitor equidistant
from the power and ground pins or, when equidistant placement
is not possible, slightly closer to the power pin. Thermal connec-
tions to the ground planes should be made on the far side of the
capacitor, as shown in Figure 14.
VDD
GND
TO GND
TO VDD
CAPACITOR
09568-
012
Figure 14. Recommended Power Supply Bypass Capacitor Layout
HANDLING INSTRUCTIONS
Pick-and-Place Equipment
The MEMS microphone can be handled using standard pick-
and-place and chip shooting equipment. Care should be taken
to avoid damage to the MEMS microphone structure as follows:
Use a standard pickup tool to handle the microphone.
Because the microphone hole is on the bottom of the
package, the pickup tool can make contact with any part
of the lid surface.
Do not pick up the microphone with a vacuum tool that
makes contact with the bottom side of the microphone.
Do not pull air out of or blow air into the microphone port.
Do not use excessive force to place the microphone on
the PCB.
Reflow Solder
For best results, the soldering profile should be in accordance
with the recommendations of the manufacturer of the solder
paste used to attach the MEMS microphone to the PCB. It is
recommended that the solder reflow profile does not exceed the
limit conditions specified in Figure 4 and Table 5.
Board Wash
When washing the PCB, ensure that water does not make
contact with the microphone port. Blow-off procedures and
ultrasonic cleaning must not be used.
SUPPORTING DOCUMENTATION
Evaluation Board User Guide
MEMS Microphone Evaluation Board
EVAL-ADMP441Z SDP Daughter Board for the
ADMP441 I2S MEMS Microphone
Circuit Note
CN-0208, High Performance Digital MEMS Microphone's Simple
Interface to SigmaDSP Audio Processor with I2S Output
CN-0266, High Performance Digital MEMS Microphone
Standard Digital Audio Interface to Blackfin DSP
Application Notes
AN-1003 Application Note, Recommendations for Mounting and
Connecting Analog Devices, Inc., Bottom-Ported MEMS
Microphones
AN-1068 Application Note, Reflow Soldering of the MEMS
Microphone
AN-1112 Application Note, Microphone Specifications and
Terms Explained
AN-1124 Application Note, Recommendations for Sealing
Analog Devices, Inc., Bottom-Port MEMS Microphones from
Dust and Liquid Ingress
AN-1140 Application Note, Microphone Array Beamfoaming
For additional information, visit www.analog.com/mic.
相關PDF資料 |
PDF描述 |
|---|---|
| ADMP504ACEZ-RL | MIC MEMS OMNI-DIR ANALOG 3LGA |
| ADMP521ACEZ-RL7 | IC MEMS MICROPHONE ULTRA LN 5LGA |
| ADN2890ACP-RL7 | IC AMP LIM 16LFCSP |
| ADN2891ACPZ-500RL7 | IC AMP LIM 16LFCSP |
| ADN2892ACPZ-500RL7 | IC AMP LIM 16LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADMP441ACEZ-RL7 | 功能描述:MIC MEMS OMNI-DIR DIGITAL 9LGA RoHS:是 類別:音頻產品 >> 麥克風 系列:ADMP441 產品目錄繪圖:SPM04xxHx(5,xH)-xB SP Series_FTPRNT-5 標準包裝:1 系列:SiSonic™ 類型:MEMS（硅） 輸出類型:模擬 方向:全向 頻率范圍:100Hz ~ 10kHz 靈敏度:-42dB ±3dB 信噪比:59dB 阻抗:100 歐姆 電壓 - 額定:1.5 ~ 3.6V 電流 - 電源:250µA 端口位置:頂部 密封等級:無 端子:表面貼裝型 尺寸/尺寸:4.72mm L x 3.76mm W 高度（最大）:1.35mm 形狀:矩形 包裝:Digi-Reel® 產品目錄頁面:2669 (CN2011-ZH PDF) 其它名稱:423-1131-6 |
| ADMP504 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ultralow Noise Microphone with Bottom Port and Analog Output |
| ADMP504ACEZ | 制造商:Analog Devices 功能描述:MIC MEMS OMNI-DIR 3LGA 制造商:Analog Devices 功能描述:MIC, MEMS, OMNI-DIR, 3LGA 制造商:Analog Devices 功能描述:MIC, MEMS, OMNI-DIR, 3LGA; Audio IC Case Style:LGA; No. of Pins:3; Operating Temperature Min:-40C; Operating Temperature Max:85C; MSL:MSL 5 - 48 hours; SVHC:No SVHC (19-Dec-2012); Control / Process Application:Industrial and ;RoHS Compliant: Yes |
| ADMP504ACEZ-RL | 功能描述:MIC MEMS OMNI-DIR ANALOG 3LGA RoHS:是 類別:音頻產品 >> 麥克風 系列:ADMP504 產品目錄繪圖:SPM04xxHx(5,xH)-xB SP Series_FTPRNT-5 標準包裝:1 系列:SiSonic™ 類型:MEMS（硅） 輸出類型:模擬 方向:全向 頻率范圍:100Hz ~ 10kHz 靈敏度:-42dB ±3dB 信噪比:59dB 阻抗:100 歐姆 電壓 - 額定:1.5 ~ 3.6V 電流 - 電源:250µA 端口位置:頂部 密封等級:無 端子:表面貼裝型 尺寸/尺寸:4.72mm L x 3.76mm W 高度（最大）:1.35mm 形狀:矩形 包裝:Digi-Reel® 產品目錄頁面:2669 (CN2011-ZH PDF) 其它名稱:423-1131-6 |
| ADMP504ACEZ-RL7 | 功能描述:MIC MEMS OMNI-DIR ANALOG 3LGA RoHS:是 類別:音頻產品 >> 麥克風 系列:ADMP504 產品目錄繪圖:SPM04xxHx(5,xH)-xB SP Series_FTPRNT-5 標準包裝:1 系列:SiSonic™ 類型:MEMS（硅） 輸出類型:模擬 方向:全向 頻率范圍:100Hz ~ 10kHz 靈敏度:-42dB ±3dB 信噪比:59dB 阻抗:100 歐姆 電壓 - 額定:1.5 ~ 3.6V 電流 - 電源:250µA 端口位置:頂部 密封等級:無 端子:表面貼裝型 尺寸/尺寸:4.72mm L x 3.76mm W 高度（最大）:1.35mm 形狀:矩形 包裝:Digi-Reel® 產品目錄頁面:2669 (CN2011-ZH PDF) 其它名稱:423-1131-6 |
發布緊急采購，3分鐘左右您將得到回復。