- 您現在的位置：買賣IC網 > PDF目錄374017 > ADN2870 (Analog Devices, Inc.) High Bandwidth, CMOS 8-Bit Serial Interface Multiplying D/A Converter; Package: MSOP; No of Pins: 10; Temperature Range: Industrial PDF資料下載
參數資料
| 型號： | ADN2870 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | High Bandwidth, CMOS 8-Bit Serial Interface Multiplying D/A Converter; Package: MSOP; No of Pins: 10; Temperature Range: Industrial |
| 中文描述： | 3.3伏雙回路，50 Mbps至3.3 Gbps的激光二極管驅動器 |
| 文件頁數： | 11/20頁 |
| 文件大小： | 764K |
| 代理商： | ADN2870 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
ADN2870
THEORY OF OPERATION
Laser diodes have a current-in to light-out transfer function as
shown in Figure 23. Two key characteristics of this transfer
function are the threshold current, Ith, and slope in the linear
region beyond the threshold current, referred to as slope
efficiency, LI.
Rev. 0 | Page 11 of 20
0
O
P1
P
AV
P
O
Ith
CURRENT
P
AV
=
P
I
ER =
P1
P
O
P1 + P
O
2
LI =
P
I
Figure 23. Laser Transfer Function
DUAL-LOOP CONTROL
Typically laser threshold current and slope efficiency are both
functions of temperature. For FP and DFB type lasers the
threshold current increases and the slope efficiency decreases
with increasing temperature. In addition, these parameters vary
as the laser ages. To maintain a constant optical average power
and a constant optical extinction ratio over temperature and
laser lifetime, it is necessary to vary the applied electrical bias
current and modulation current to compensate for the lasers
changing LI characteristics.
Single-loop compensation schemes use the average monitor
photodiode current to measure and maintain the average
optical output power over temperature and laser aging. The
ADN2870 is a dual-loop device, implementing both this
primary average power control loop and, additionally, a
secondary control loop, which maintains constant optical
extinction ratio. The dual-loop control of average power and
extinction ratio implemented in the ADN2870 can be used
successfully both with lasers that maintain good linearity of LI
transfer characteristics over temperature and with those that
exhibit increasing nonlinearity of the LI characteristics over
temperature.
Dual Loop
The ADN2870 uses a proprietary patented method to control
both average power and extinction ratio. The ADN2870 is
constantly sending a test signal on the modulation current
signal and reading the resulting change in the MPD current as a
means of detecting the slope of the laser in real time. This
information is used in a servo to control the ER of the laser,
which is done in a time-multiplexed manner at a low frequency,
typically 80 Hz. Figure 24 shows the dual-loop control
implementation on the ADN2870.
0
ERSET
IMPD
I
PA
PAVSET
I
EX
Φ
1
Φ
2
Φ
2
Φ
2
OPTICAL COUPLING
SHA
CMOD
Gm
1.2V
V
BGAP
100
2
BIAS
CURRENT
VCC
HIGH
SPEED
Figure 24. Dual-Loop Control of Average Power and Extinction Ratio
A dual loop is made up of an APCL (average power control
loop) and the ERCL (extinction ratio control loop), which are
separated into two time states. During time Φ1, the APC loop is
operating, and during time Φ2, the ER loop is operating.
Average Power Control Loop
The APCL compensates for changes in Ith and LI by varying
Ibias. APC control is performed by measuring MPD current,
Impd. This current is bandwidth-limited by the MPD. This is
not a problem because the APCL must be low frequency since
the APCL must respond to the average current from the MPD.
The APCL compares Impd × Rpavset to the BGAP voltage,
Vbgap. If Impd falls, the bias current is increased until Impd ×
Rpavset equals Vbgap. Conversely, if the Impd increases, Ibias
is decreased.
Modulation Control Loop
The ERCL measures the slope efficiency, LI, of the LD, and
changes Imod as LI changes. During the ERCL, Imod is
temporarily increased by
Imod. The ratio between Imod and
Imod is a fixed ratio of 50:1, but during startup, this ratio is
increased in order to decrease settling time.
During ERCL, switching in
Imod causes a temporary increase
in average optical power,
Pav. However the APC loop is dis-
abled during ERCL, and the increase is kept small enough so as
not to disturb the optical eye. When
Imod is switched into the
laser circuit, an equal current, Iex, is switched into the PAVSET
resistor. The user sets the value of Iex; this is the ERSET setpoint.
If
Impd is too small, the control loop knows that LI has
decreased and increases Imod and, therefore,
Imod accordingly
until
Impd is equal to Iex. The previous time state values of
the bias and mod settings are stored on the hold capacitors
PAVCAP and ERCAP.
The ERCL is constantly measuring the actual LI curve, therefore
it compensates for the effects of temperature and for changes in
the LI curve due to laser aging. Thus the laser may be calibrated
once at 25°C and can then automatically control the laser over
temperature. This eliminates expensive and time consuming
temperature calibration of the laser.
相關PDF資料 |
PDF描述 |
|---|---|
| ADN2870ACPZ | High Bandwidth, CMOS 8-Bit Serial Interface Multiplying D/A Converter; Package: MSOP; No of Pins: 10; Temperature Range: Industrial |
| ADN2870ACPZ-RL | 3.3 V Dual-Loop, 50 Mbps to 3.3 Gbps Laser Diode Driver |
| ADN2870ACPZ-RL7 | 3.3 V Dual-Loop, 50 Mbps to 3.3 Gbps Laser Diode Driver |
| ADN2890 | 3.3 V 2.7 Gb/s Limiting Amplifier |
| ADN2890ACP | 3.3 V 2.7 Gb/s Limiting Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2870ACP | 制造商:Analog Devices 功能描述:LASER DRVR DFB 3.3GBPS 1CH 24LFCSP - Bulk |
| ADN2870ACPZ | 功能描述:IC LSR DRVR 3.3GPBS 3.6V 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| ADN2870ACPZ-RL | 功能描述:IC LSR DRVR 3.3GPBS 3.6V 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| ADN2870ACPZ-RL7 | 功能描述:IC LSR DRVR 3.3GPBS 3.6V 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| ADN2871 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.3 V, 50 Mbps to 4.25 Gbps Single-Loop Laser Diode Driver |
發布緊急采購，3分鐘左右您將得到回復。