- 您現在的位置：買賣IC網 > PDF目錄165352 > ADNS-3550 (Avago Technologies Ltd.) Low Power LED Integrated Slim Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNS-3550 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | Low Power LED Integrated Slim Mouse Sensor |
| 中文描述： | 小功率LED集成超薄鼠標傳感器 |
| 文件頁數： | 7/28頁 |
| 文件大?。?/td> | 496K |
| 代理商： | ADNS-3550 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
15
Burst Mode Operation
Burst mode is a special serial port operation mode that
may be used to reduce the serial transaction time for
a motion read. The speed improvement is achieved
by continuous data clocking from multiple registers
without the need to specify the register address, and
by not requiring the normal delay period between data
bytes.
Burst mode is activated by reading the Motion_Burst
register. The ADNS-3550 will respond with the contents
of the Motion, Delta_Y, Delta_X, SQUAL, Shutter_Upper,
Shutter_Lower and Maximum_Pixel registers in that
order. The burst transaction can be terminated after the
first three bytes of the sequence are read by bringing
the NCS pin high. After sending the register address, the
microcontroller must wait tSRAD and then begin reading
data. All data bits can be read with no delay between
bytes by driving SCLK at the normal rate. The data is
latched into the output buffer after the last address bit
is received. After the burst transmission is complete, the
microcontroller must raise the NCS line for at least tBEXIT
to terminate burst mode. The serial port is not available
for use until it is reset with NCS, even for a second burst
transmission.
Figure 18. Motion burst timing
Notes on Power-Up
The ADNS-3550 does not perform an internal power
up self-reset; the POWER_UP_RESET register must be
written every time power is applied. The appropriate
sequence is as follows:
1. Apply power
2. Drive NCS high, then low to reset the SPI port
3. Write 0x5a to register 0x3a
4. Read from registers 0x02, 0x03 and 0x04 (or read
these same three bytes from burst motion register
0x42) one time regardless the state of the motion
pin.
During power-up there will be a period of time after the
power supply is high but before any clocks are available.
The table below shows the state of the various pins
during power-up and reset.
State of Signal Pins After VDD is Valid
Pin
On Power-Up
NCS High Before Reset
NCS Low Before Reset
After Reset
NCS
Functional
High
Low
Functional
MISO
Undefined
Functional
Depends on NCS
SCLK
Ignored
Functional
Depends on NCS
MOSI
Ignored
Functional
Depends on NCS
XY_LED
Undefined
Functional
MOTION
Undefined
Functional
SHTDWN
Must Be Low
Functional
MOTION_BURST REGISTER ADDRESS
READ FIRST BYTE
FIRST READ OPERATION
READ SECOND BYTE
READ THIRD BYTE
SCLK
tSRAD
相關PDF資料 |
PDF描述 |
|---|---|
| ADP-304F-11-000-02 | 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| ADP-304F-01-000-02 | 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| ADP1110AN-33 | Micropower, Step-Up/Step-Down Switching Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
| ADP1110AN | Micropower, Step-Up/Step-Down Switching Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
| ADP1110AN-12 | Micropower, Step-Up/Step-Down Switching Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-4000 | 功能描述:光學導航傳感器 Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-4005 | 功能描述:光學導航傳感器 Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-4010 | 功能描述:光學導航傳感器 Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-4700 | 功能描述:光學導航傳感器 Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5000 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。