- 您現在的位置：買賣IC網 > PDF目錄362144 > ADS7800BH 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS7800BH |
| 英文描述： | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
| 中文描述： | 12位為3ms采樣模擬到數字轉換器 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 122K |
| 代理商： | ADS7800BH |
9
ADS7800
FIGURE 6. Convert Mode: R/C Pulse LOW — Outputs Enabled After Conversion.
INTERNAL CLOCK
The ADS7800 has an internal clock that is factory trimmed
to achieve a typical conversion time of 2.47
μ
s, and a
maximum conversion time over the full operating tempera-
ture range of 2.7
μ
s. No external adjustments are required,
and with the guaranteed maximum acquisition time of
300ns, throughput performance is assured with convert
pulses as close as 3
μ
s.
READING DATA
After conversion is initiated, the output buffers remain in a
Hi-Z state until the following three logic conditions are
simultaneously met: R/C is HIGH, BUSY is HIGH and CS
is LOW. Upon satisfaction of these conditions, the data lines
are enabled according to the state of HBE. See Figure 9 and
Table III for timing relationships and specifications.
CALIBRATION
OPTIONAL EXTERNAL GAIN AND OFFSET TRIM
Offset and full-scale errors may be trimmed to zero using
external offset and full-scale trim potentiometers connected
to the ADS7800 as shown in Figures 10 and 11.
If adjustment of offset and full scale is not required,
connections as shown in Figures 4 and 5 should be used.
CALIBRATION PROCEDURE
First, trim offset, by applying at the input (pin 1 or 2) the
mid-point transition voltage (–2.44mV for the
±
10V range,
–1.22mV for the
±
5V range.) With the ADS7800 converting
continually, adjust potentiometer R
1
until the MSB (D11 on
pin 5) is toggling alternately HIGH and LOW.
Next adjust full scale, by applying at the input a DC input
signal that is 3/2LSB below the nominal full scale voltage
(+9.9927V for the
±
10V range, +4.9963V for the
±
5V
range.) With the ADS7800 converting continually, adjust
R
2
until the LSB (D0 on pin 17) is toggling HIGH and LOW
with all of the other bits HIGH.
LAYOUT CONSIDERATIONS
Because of the high resolution and linearity of the ADS7800,
system design problems such as ground path resistance and
contact resistance become very important.
ANALOG SIGNAL SOURCE IMPEDANCE
The input resistance of the ADS7800 is 6.3k
or 4.2k
(for
the
±
10V and
±
5V ranges respectively.) To avoid introduc-
ing distortion, the source resistance must be very low, or
constant with signal level. The output impedance provided
by most op amps is ideal.
Pins 23 (V
SD
) and 24 (V
SA
) are not connected internally
on the ADS7800, to maximize accuracy on the chip. They
should be connected together as close as possible to the unit.
R/C
Converter
Mode
BUSY
Data
BUS
t
W
Acquire
Convert
Acquire
Convert
Data Valid
Hi-Z State
Data Valid
Hi-Z State
t
DBC
t
AP
t
B
t
DBE
t
A
t
DB
t
C
t
HDR
and t
HL
1
2
ADS7800
±5V
Input
FIGURE 4.
±
10V Range Without Trims.
1
2
ADS7800
±10V
Input
FIGURE 5.
±
5V Range Without Trims.
相關PDF資料 |
PDF描述 |
|---|---|
| ADS7800JP | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7800JU | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7800KU | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7803 | ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting |
| ADS7803BN | Autocalibrating, 4-Channel, 12-Bit ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7800JP | 功能描述:模數轉換器 - ADC 12-Bit 3us Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7800JP | 制造商:BURR-BROWN 功能描述:12BIT ADC SAMPLING 7800 DIP24 |
| ADS7800JPG4 | 功能描述:模數轉換器 - ADC 12-Bit 3us Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7800JU | 功能描述:模數轉換器 - ADC 12-Bit 3us Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7800JU/1K | 功能描述:模數轉換器 - ADC 12-Bit 3us Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發(fā)布緊急采購，3分鐘左右您將得到回復。