- 您現在的位置：買賣IC網 > PDF目錄17000 > ADS8364EVM (Texas Instruments)EVALUATION MODULE FOR BQ2018 PDF資料下載
參數資料
| 型號： | ADS8364EVM |
| 廠商： | Texas Instruments |
| 文件頁數： | 5/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION MODULE FOR BQ2018 |
| 產品培訓模塊： | Data Converter Basics |
| 標準包裝： | 1 |
| ADC 的數量： | 6 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 并聯 |
| 輸入范圍： | 0 ~ 5 V |
| 在以下條件下的電源（標準）： | 413.5mW @ 250kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | ADS8364 |
| 已供物品： | 板 |
| 相關產品： | 296-13449-6-ND - IC ADC LP 16BIT 250KSPS 64TQFP ADS8364Y/2KG4-ND - IC ADC LP 16BIT 250KSPS 64-TQFP ADS8364Y/2K-ND - IC ADC LP 16BIT 250KSPS 64-TQFP ADS8364Y/250G4-ND - IC ADC LP 16BIT 250KSPS 64-TQFP 296-13449-1-ND - IC ADC LP 16BIT 250KSPS 64TQFP 296-13449-2-ND - IC ADC LP 16BIT 250KSPS 64TQFP |
ADS8364
13
SBAS219C
www.ti.com
EOC
—End of conversion goes low when new data of the
internal ADC is latched into the output registers, which
usually happens 16.5 clock cycles after hold initiated the
conversion. It remains low for half a clock cycle. If more than
one channel pair is converted simultaneously, the
A-channels get stored to the registers first (16.5 clock cycles
after hold), followed by the B-channels one clock cycle later,
and finally the C-channels at another clock cycle later. If a
reading (RD and CS are LOW) is in process, then the latch
process is delayed until the read operation is finished.
FD—First data or A0 data is HIGH if channel A0 is chosen to be
read next. In the FIFO mode whatever channel X0 is written to
the FIFO first is latched into the A0 register. So, for example,
when the FIFO is empty, FD is 0. Then the first result is latched
into the FIFO register A0 is, therefore, chosen to be read next,
and FD rises. After the first channel is read (1-3 read cycles
depending on BYTE and ADD) FD goes LOW again.
START OF A CONVERSION AND READING DATA
By bringing one, two, or all of the HOLDX signals LOW, the
input data of the corresponding channel X is immediately
placed in the hold mode (5ns). The conversion of this channel
X follows with the next rising edge of clock. If it is important to
detect a hold command during a certain clock-cycle, then the
falling edge of the hold signal has to occur at least 10ns before
the rising edge of clock, as shown in Figure 7, tD1. The hold
signal can remain LOW without initiating a new conversion.
The hold signal has to be HIGH for at least 15ns (as shown
in Figure 7, tW2) before it is brought LOW again and hold has
to stay LOW for at least 20ns (Figure 7, tW3).
Once a particular hold signal goes low, further impulses of
this hold signal are ignored until the conversion is finished or
the part is reset. When the conversion is finished (after 16
clock cycles) the sampling switches will close and sample the
selected channel. The start of the next conversion must be
delayed to allow the input capacitor of the ADS8364 to be
fully charged. This delay time depends on the driving ampli-
fier, but should be at least 800ns.
FIGURE 7. Start of the Conversion.
The ADS8364 can also convert one channel continuously
(see Figure 8). Therefore, HOLDA and HOLDC are kept
HIGH all the time. To gain acquisition time, the falling edge
of HOLDB takes place just before the rising edge of clock.
One conversion requires 20 clock cycles. Here, data is read
after the next conversion is initiated by HOLDB. To read data
from channel B, A1 is set HIGH and A2 is LOW. As A0 is
LOW during the first reading (A2 A1 A0 = 010) data B0 is put
to the output. Before the second RD, A0 switches HIGH (A2
A1 A0 = 011) so data from channel B1 is read, as shown in
Table II. However, reading data during the conversion or on a
falling hold edge might cause a loss in performance.
A2
A1
A0
CHANNEL TO BE READ
0
CHA0
0
1
CHA1
0
1
0
CHB0
0
1
CHB1
1
0
CHC0
1
0
1
CHC1
1
0
Cycle mode reads registers
CHA0 through CHC1 on
successive transitions of the
read line.
1
FIFO Mode
TABLE II. Address Control for RD Functions.
Reading data (RD, CS )—In general, the channel/data
outputs are in tri-state. Both CS and RD have to be LOW to
enable these outputs. RD and CS have to stay LOW to-
gether for at least 40ns (see Timing Characteristics, tD6)
before the output data is valid. RD has to remain HIGH for
at least 30ns (see Timing Diagram, tW5) before bringing it
back LOW for a subsequent read command.
16.5 clock-cycles after the start of a conversion (next rising
edge of clock after the falling edge of HOLDX ), the new data
is latched into its output register. Even if the ADS8364 is
forced to wait until the read process is finished (RD signal
going HIGH) before the new data gets latched into its output
t
C1
t
W1
t
W3
t
W2
t
D2
t
W4
t
D1
CLK
HOLD A
RESET
HOLD B
HOLD C
相關PDF資料 |
PDF描述 |
|---|---|
| 101A052-3/42-0 | BOOT MOLDED |
| SRR0906-472YL | INDUCTOR PWR 4700UH 15% SHLD SMD |
| EBA14DRMT-S288 | CONN EDGECARD 28POS .125 EXTEND |
| LGU2W221MELA | CAP ALUM 220UF 450V 20% SNAP |
| HFI-160808-R15J | INDUCTOR 1.6X0.8X0.8MM 150NH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS8364M-EVM | 功能描述:數據轉換 IC 開發工具 ADC CONVERTER RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADS8364Y | 制造商:TI 制造商全稱:Texas Instruments 功能描述:250kHz, 16-Bit, 6-Channel Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTERS |
| ADS8364Y/250 | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8364Y/250G4 | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8364Y/2K | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。