VCC+ VCC- 1 k 1 " />
參數資料
型號: ADS8412IBPFBR
廠商: Texas Instruments
文件頁數: 14/30頁
文件大?。?/td> 0K
描述: IC ADC 16BIT 2MSPS 48-TQFP
產品培訓模塊: Data Converter Basics
標準包裝: 1,000
位數: 16
采樣率(每秒): 2M
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 200mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-TQFP
供應商設備封裝: 48-TQFP(7x7)
包裝: 帶卷 (TR)
輸入數目和類型: 1 個差分,單極
配用: 296-18385-ND - EVALUATION MODULE FOR ADS8412
www.ti.com
_
+
_
+
IN-
IN+
ADS8412
_
+
VCC+
VCC-
1 k
1 k
THS4503
68 pF
50
50
20 pF
RG
RS
RT
OCM
1 k
RG, RS, and RT should be chosen such that
RG + RS || RT = 1 k
VOCM = 2 V, +VCC = 7 V, and -VCC = -7 V
DIGITAL INTERFACE
Timing And Control
Reading Data
ADS8412
SLAS384A – JUNE 2003 – REVISED DECEMBER 2004
PRINCIPLES OF OPERATION (continued)
Figure 31. Using THS4503 With ADS8412
See the timing diagrams in the specifications section for detailed information on timing signals and their
requirements.
The ADS8412 uses an internal oscillator generated clock which controls the conversion rate and in turn the
throughput of the converter. No external clock input is required.
Conversions are initiated by bringing the CONVST pin low for a minimum of 20 ns (after the 20 ns minimum
requirement has been met, the CONVST pin can be brought high), while CS is low. The ADS8412 switches from
the sample to the hold mode on the falling edge of the CONVST command. A clean and low jitter falling edge of
this signal is important to the performance of the converter. The BUSY output is brought high after CONVST
goes low. BUSY stays high throughout the conversion process and returns low when the conversion has ended.
Sampling starts when CS is tied low or starts with the falling edge of CS when BUSY is low.
Both RD and CS can be high during and before a conversion with one exception (CS must be low when
CONVST goes low to initiate a conversion). Both the RD and CS pins are brought low in order to enable the
parallel output bus with the conversion.
The ADS8412 outputs full parallel data in two's complement format as shown in Table 1. The parallel output is
active when CS and RD are both low. There is a minimal quiet zone requirement around the falling edge of
CONVST. This is 50 ns prior to the falling edge of CONVST and 40 ns after the falling edge. No data read should
be attempted within this zone. Any other combination of CS and RD sets the parallel output to 3-state. BYTE is
used for multiword read operations. BYTE is used whenever lower bits of the conversion result are output on the
higher byte of the bus. Refer to Table 1 for ideal output codes.
21
相關PDF資料
PDF描述
D38999/20WC98PBLC CONN HSG RCPT 10POS WALL MT PINS
D38999/20WD18SNLC CONN HSG RCPT 18POS WALL MT SCKT
D38999/20FD18BN CONN HSG RCPT 18POS WALL MT SCKT
MS27467T13B8SLC CONN HSG PLUG 8POS STRGHT SCKT
D38999/24WD19AN CONN HSG RCPT 19POS JAM NUT PINS
相關代理商/技術參數
參數描述
ADS8412IBPFBRG4 功能描述:模數轉換器 - ADC 16 Bit 2MSPS Parallel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS8412IBPFBT 功能描述:模數轉換器 - ADC 16 Bit 2MSPS Parallel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS8412IBPFBT 制造商:Texas Instruments 功能描述:IC ADC 16BIT 2MSPS ((NW))
ADS8412IBPFBTG4 功能描述:模數轉換器 - ADC 16 Bit 2MSPS Parallel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS8412IPFB 制造商:Texas Instruments 功能描述:16 BIT 2MSPS PARALLEL ADC W/REF, PSEUDO BIPOLAR FULLY DIFFER - Rail/Tube