- 您現在的位置：買賣IC網 > PDF目錄19376 > ADSP-21061KS-133 (Analog Devices Inc)IC DSP CONTROLLER 32BIT 240MQFP PDF資料下載
參數資料
| 型號： | ADSP-21061KS-133 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 38/52頁 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 32BIT 240MQFP |
| 產品培訓模塊： | SHARC Processor Overview |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | 同步串行端口（SSP） |
| 時鐘速率： | 33MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 128kB |
| 電壓 - 輸入/輸出： | 5.00V |
| 電壓 - 核心： | 5.00V |
| 工作溫度： | 0°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 240-BFQFP 裸露焊盤 |
| 供應商設備封裝： | 240-MQFP-EP（32x32） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Rev. D | Page 43 of 52 | May 2013
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they stop driv-
ing, go into a high impedance state, and start to decay from their
output high or low voltage. The time for the voltage on the bus
to decay by V is dependent on the capacitive load, CL, and the
load current, IL. This decay time can be approximated by the
following equation:
The output disable time tDIS is the difference between
the interval from when the reference signal switches to when the
output voltage decays V from the measured output high or
output low voltage. tDECAY is calculated with test loads CL and IL,
and with V equal to 0.5 V.
Output Enable Time
Output pins are considered to be enabled when they have made
a transition from a high impedance state to when they start driv-
ing. The output enable time tENA is the interval from when a
reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram (Figure 27). If multiple
pins (such as the data bus) are enabled, the measurement value
is that of the first pin to start driving.
Example System Hold Time Calculation
To determine the data output hold time in a particular system,
first calculate tDECAY using the equation given above. Choose V
to be the difference between the ADSP-21061’s output voltage
and the input threshold for the device requiring the hold time. A
typical V will be 0.4 V. CL is the total bus capacitance (per data
line), and IL is the total leakage or three-state current (per data
line). The hold time will be tDECAY plus the minimum disable
time (i.e., tDATRWH for the write cycle).
Output Drive Characteristics
output drivers of the ADSP-21061 (5 V) and ADSP-21061L
(3 V). The curves represent the current drive capability and
switching behavior of the output drivers as a function of
resistive and capacitive loading.
Capacitive Loading
Output delays and holds are based on standard capacitive loads:
50 pF on all pins (see Figure 28). The delay and hold specifica-
tions given should be derated by a factor of 1.5 ns/50 pF for
loads other than the nominal value of 50 pF. Figure 31,
cally how output delays and holds vary with load capacitance.
(Note that this graph or derating does not apply to output dis-
able delays; see the previous section Output Disable Time under
Test Conditions.) The graphs of Figure 31, Figure 32, Figure 35,
and Figure 36 may not be linear outside the ranges shown.
Figure 27. Output Enable/Disable
PEXT
CL V
IL
---------------
=
REFERENCE
SIGNAL
tDIS
OUTPUT STARTS
DRIVING
VOH (MEASURED) - V
VOL (MEASURED) + V
tMEASURED
VOH (MEASURED)
VOL (MEASURED)
2.0V
1.0V
VOH (MEASURED)
VOL (MEASURED)
HIGH IMPEDANCE STATE.
TESTCONDITIONS CAUSE
THIS VOLTAGE TO BE
APPROXIMATELY 1.5V.
OUTPUT STOPS
DRIVING
tENA
tDECAY
Figure 28. Equivalent Device Loading for AC Measurements (Includes All
Fixtures)
Figure 29. Voltage Reference Levels for AC Measurements (Except Output
Enable/Disable)
1.5V
50pF
TO
OUTPUT
PIN
IOL
IOH
INPUT
OR
OUTPUT
1.5V
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6665ASA60+T | IC FAN CNTRL/DRVR 8-SOIC |
| VI-B32-CY-F3 | CONVERTER MOD DC/DC 15V 50W |
| HWS300-3 | PWR SUP IND 3.3V 60A SNG OUTPUT |
| ADSP-21061KSZ-133 | IC DSP CONTROLLER 32BIT 240MQFP |
| VI-B31-CY-F2 | CONVERTER MOD DC/DC 12V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21061KS-160 | 功能描述:IC DSP CONTROLLER 1MBIT 240MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061KS-200 | 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061KS-200X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Digital Signal Processor |
| ADSP-21061KSZ-133 | 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061KSZ-160 | 功能描述:IC DSP CONTROLLER 1MBIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
發布緊急采購，3分鐘左右您將得到回復。