參數資料
型號： ADSP-21062KS-160
廠商： Analog Devices Inc
文件頁數： 2/64頁
文件大小： 0K
描述： IC DSP CONTROLLER 2MBIT 240MQFP
產品培訓模塊： SHARC Processor Overview
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： 主機接口，連接端口，串行端口
時鐘速率： 40MHz
非易失內存： 外部
芯片上RAM： 256kB
電壓 - 輸入/輸出： 5.00V
電壓 - 核心： 5.00V
工作溫度： 0°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 240-BFQFP 裸露焊盤
供應商設備封裝： 240-MQFP-EP（32x32）
包裝： 托盤
Rev. F
|
Page 10 of 64
|
March 2008
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
PIN FUNCTION DESCRIPTIONS
The ADSP-2106x pin definitions are listed below. Inputs identi-
fied as synchronous (S) must meet timing requirements with
respect to CLKIN (or with respect to TCK for TMS, TDI).
Inputs identified as asynchronous (A) can be asserted asynchro-
nously to CLKIN (or to TCK for TRST).
Unused inputs should be tied or pulled to VDD or GND, except
for ADDR31–0, DATA47–0, FLAG3–0, and inputs that have
internal pull-up or pull-down resistors (CPA, ACK, DTx, DRx,
TCLKx, RCLKx, LxDAT3–0, LxCLK, LxACK, TMS, and
TDI)—these pins can be left floating. These pins have a
logic-level hold circuit that prevents the input from floating
internally.
Table 3. Pin Descriptions
Pin
Type
Function
ADDR31–0
I/O/T
External Bus Address. The ADSP-2106x outputs addresses for external memory and peripherals on these
pins. In a multiprocessor system, the bus master outputs addresses for read/write of the internal memory
or IOP registers of other ADSP-2106xs. The ADSP-2106x inputs addresses when a host processor or multi-
processing bus master is reading or writing its internal memory or IOP registers.
DATA47–0
I/O/T
External Bus Data. The ADSP-2106x inputs and outputs data and instructions on these pins. 32-bit single-
precision floating-point data and 32-bit fixed-point data is transferred over bits 47–16 of the bus. 40-bit
extended-precision floating-point data is transferred over bits 47–8 of the bus. 16-bit short word data is
transferred over bits 31–16 of the bus. In PROM boot mode, 8-bit data is transferred over bits 23–16. Pull-up
resistors on unused DATA pins are not necessary.
MS3–0
O/T
Memory Select Lines. These lines are asserted (low) as chip selects for the corresponding banks of external
memory. Memory bank size must be defined in the ADSP-2106x’s system control register (SYSCON). The
MS3–0 lines are decoded memory address lines that change at the same time as the other address lines.
When no external memory access is occurring, the MS3–0 lines are inactive; they are active however when
a conditional memory access instruction is executed, whether or not the condition is true. MS0 can be used
with the PAGE signal to implement a bank of DRAM memory (Bank 0). In a multiprocessing system the MS3–0
lines are output by the bus master.
RD
I/O/T
Memory Read Strobe. This pin is asserted (low) when the ADSP-2106x reads from external memory devices
or from the internal memory of other ADSP-2106xs. External devices (including other ADSP-2106xs) must
assert RD to read from the ADSP-2106x’s internal memory. In a multiprocessing system, RD is output by the
bus master and is input by all other ADSP-2106xs.
WR
I/O/T
Memory Write Strobe. This pin is asserted (low) when the ADSP-2106x writes to external memory devices
or to the internal memory of other ADSP-2106xs. External devices must assert WR to write to the ADSP-
2106x’s internal memory. In a multiprocessing system, WR is output by the bus master and is input by all
other ADSP-2106xs.
PAGE
O/T
DRAM Page Boundary. The ADSP-2106x asserts this pin to signal that an external DRAM page boundary
has been crossed. DRAM page size must be defined in the ADSP-2106x’s memory control register (WAIT).
DRAM can only be implemented in external memory Bank 0; the PAGE signal can only be activated for Bank
0 accesses. In a multiprocessing system, PAGE is output by the bus master
ADRCLK
O/T
Clock Output Reference. In a multiprocessing system, ADRCLK is output by the bus master.
SW
I/O/T
Synchronous Write Select. This signal is used to interface the ADSP-2106x to synchronous memory devices
(including other ADSP-2106xs). The ADSP-2106x asserts SW (low) to provide an early indication of an
impending write cycle, which can be aborted if WR is not later asserted (e.g., in a conditional write
instruction). In a multiprocessing system, SW is output by the bus master and is input by all other
ADSP-2106xs to determine if the multiprocessor memory access is a read or write. SW is asserted at the same
time as the address output. A host processor using synchronous writes must assert this pin when writing to
the ADSP-2106x(s).
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
相關PDF資料
PDF描述
HWS300-24/ME PWRSUP IND MEDICAL 24V 336W 14A
ACB60DHFN-S621 EDGECARD 120POS .050 PCI32 SMD
RW-0512D CONV DC/DC 3W 4.5-9VIN +/-12VOUT
MAX6646YMUA+T IC SENSOR REMOTE SMBUS 8UMAX
VJ1206A150KBCAT4X CAP CER 15PF 200V 10% NP0 1206
相關代理商/技術參數
參數描述
ADSP-21062KSZ-133 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-21062KSZ-160 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21062L 制造商:AD 制造商全稱:Analog Devices 功能描述:ADSP-2106x SHARC DSP Microcomputer Family
ADSP-21062LAB-160 功能描述:IC DSP CONTROLLER 32BIT 225BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21062LABZ-160 功能描述:IC DSP CONTROLLER 32BIT 225BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*