- 您現在的位置：買賣IC網 > PDF目錄19391 > ADSP-21488KSWZ-3A (Analog Devices Inc)IC CCD SIGNAL PROCESSOR 100LQFP PDF資料下載
參數資料
| 型號： | ADSP-21488KSWZ-3A |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD SIGNAL PROCESSOR 100LQFP |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | EBI/EMI，DAI，I²C，SPI，SPORT，UART/USART |
| 時鐘速率： | 350MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 3Mb |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.10V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP 裸露焊盤 |
| 供應商設備封裝： | 100-LQFP-EP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Rev. B
|
Page 22 of 68
|
March 2013
TIMING SPECIFICATIONS
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results
for an individual device, the values given in this data sheet
reflect statistical variations and worst cases. Consequently, it is
not meaningful to add parameters to derive longer times. See
Figure 43 on Page 55 for voltage reference levels.
Switching Characteristics specify how the processor changes its
signals. Circuitry external to the processor must be designed for
compatibility with these signal characteristics. Switching char-
acteristics describe what the processor will do in a given
circumstance. Use switching characteristics to ensure that any
timing requirement of a device connected to the processor (such
as memory) is satisfied.
Timing Requirements apply to signals that are controlled by cir-
cuitry external to the processor, such as the data input for a read
operation. Timing requirements guarantee that the processor
operates correctly with other devices.
Core Clock Requirements
The processor’s internal clock (a multiple of CLKIN) provides
the clock signal for timing internal memory, the processor core,
and the serial ports. During reset, program the ratio between the
processor’s internal clock frequency and external (CLKIN)
clock frequency with the CLK_CFG1–0 pins.
The processor’s internal clock switches at higher frequencies
than the system input clock (CLKIN). To generate the internal
clock, the processor uses an internal phase-locked loop (PLL,
see Figure 4). This PLL-based clocking minimizes the skew
between the system clock (CLKIN) signal and the processor’s
internal clock.
Voltage Controlled Oscillator (VCO)
In application designs, the PLL multiplier value should be
selected in such a way that the VCO frequency never exceeds
The product of CLKIN and PLLM must never exceed 1/2 of
(INDIV = 0).
The product of CLKIN and PLLM must never exceed fVCO
(max) in Table 20 if the input divider is enabled
(INDIV = 1).
The VCO frequency is calculated as follows:
fVCO = 2 × PLLM × fINPUT
fCCLK = (2 × PLLM × fINPUT) ÷ PLLD
where:
fVCO = VCO output
PLLM = Multiplier value programmed in the PMCTL register.
During reset, the PLLM value is derived from the ratio selected
using the CLK_CFG pins in hardware.
PLLD = 2, 4, 8, or 16 based on the divider value programmed on
the PMCTL register. During reset this value is 2.
fINPUT = is the input frequency to the PLL.
fINPUT = CLKIN when the input divider is disabled or
fINPUT = CLKIN ÷ 2 when the input divider is enabled
Figure 4. Core Clock and System Clock Relationship to CLKIN
LOOP
FILTER
CLKIN
PCLK
SDRAM
DIVIDER
BYPASS
MUX
PMCTL
(SDCKR)
CCLK
PLL
XTAL
CLKIN
DIVIDER
RESET
f
VCO ÷ (2 × PLLM)
BUF
VCO
BUF
PMCTL
(INDIV)
PLL
DIVIDER
RESETOUT
CLKOUT (TEST ONLY)*
DELAY OF
4096 CLKIN
CYCLES
PCLK
PMCTL
(PLLBP)
PMCTL
(PLLD)
f
VCO
f
CCLK
fINPUT
*CLKOUT (TEST ONLY) FREQUENCY IS THE SAME AS f
INPUT.
THIS SIGNAL IS NOT SPECIFIED OR SUPPORTED FOR ANY DESIGN.
CLK_CFGx/
PMCTL (2 × PLLM)
DIVIDE
BY 2
PIN
MUX
PMCTL
(PLLBP)
CCLK
RESETOUT
CORESRST
SDCLK
BYPASS
MUX
相關PDF資料 |
PDF描述 |
|---|---|
| RCM12DCAN | CONN EDGECARD 24POS R/A .156 SLD |
| VI-24Z-CX-F3 | CONVERTER MOD DC/DC 2V 30W |
| DSEI36-06AS | DIODE FRED 600V 37A TO-263AB |
| ADSP-BF525KBCZ-5 | IC DSP CTRLR 16B 533MHZ 289BGA |
| LP2950ACDT-5.0 | IC REG LDO 5V .1A DPAK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21488KSWZ-3A1 | 功能描述:IC DSP SHARC 400MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21488KSWZ-3B | 功能描述:IC CCD SIGNAL PROCESSOR 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21488KSWZ-4A | 功能描述:IC CCD SIGNAL PROCESSOR 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21488KSWZ-4B | 功能描述:IC CCD SIGNAL PROCESSOR 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21488KSWZ-4B1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SHARC Processor |
發布緊急采購，3分鐘左右您將得到回復。