參數資料
型號: ADSP-2189NBSTZ-320
廠商: Analog Devices Inc
文件頁數: 18/48頁
文件大小: 0K
描述: IC DSP CONTROLLER 16BIT 100-LQFP
標準包裝: 1
系列: ADSP-21xx
類型: 定點
接口: 主機接口,串行端口
時鐘速率: 80MHz
非易失內存: 外部
芯片上RAM: 192kB
電壓 - 輸入/輸出: 1.8V,2.5V,3.3V
電壓 - 核心: 1.90V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-LQFP(14x14)
包裝: 托盤
ADSP-218xN
Rev. A
|
Page 25 of 48
|
August 2006
ENVIRONMENTAL CONDITIONS
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured out-
put high or low voltage to a high impedance state. The output
disable time (tDIS) is the difference of tMEASURED and tDECAY, as
shown in Figure 20. The time is the interval from when a refer-
ence signal reaches a high or low voltage level to when the
output voltages have changed by 0.5 V from the measured out-
put high or low voltage.
The decay time, tDECAY, is dependent on the capacitive load, CL,
and the current load, iL, on the output pin. It can be approxi-
mated by the following equation:
from which
is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.
Output Enable Time
Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start
driving. The output enable time (tENA) is the interval from when
a reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in Figure 20. If multiple pins (such as the data bus) are enabled,
the measurement value is that of the first pin to start driving.
Table 14. Thermal Resistance
Rating Description
1
1 Where the Ambient Temperature Rating (TAMB) is:
TAMB = TCASE – (PD × θCA)
TCASE = Case Temperature in °C
PD = Power Dissipation in W
Symbol
LQFP
(
°C/W)
BGA
(
°C/W)
Thermal Resistance (Case-
to-Ambient)
θ
CA
48
63.3
Thermal Resistance
(Junction-to-Ambient)
θ
JA
50
70.7
Thermal Resistance
(Junction-to-Case)
θ
JC
27.4
Figure 18. Voltage Reference Levels for AC Measurements (Except Output
Enable/Disable)
Figure 19. Equivalent Loading for AC Measurements (Including All Fixtures)
1.5V
OUTPUT
INPUT
1.5V
2.0V
0.8V
TO
OUTPUT
PIN
50pF
1.5V
I
OH
IOL
Figure 20. Output Enable/Disable
2.0V
1.0V
tENA
REFERENCE
SIGNAL
OUTPUT
tDECAY
VOH
(MEASURED)
OUTPUT STOPS
DRIVING
OUTPUT STARTS
DRIVING
tDIS
tMEASURED
VOL
(MEASURED)
VOH (MEASURED) – 0.5V
VOL (MEASURED) + 0.5V
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
VOH
(MEASURED)
VOL
(MEASURED)
tDECAY
CL 0.5V
×
iL
------------------------
=
tDIS
tMEASURED tDECAY
=
相關PDF資料
PDF描述
HSM36DRTF CONN EDGECARD 72POS DIP .156 SLD
ADSP-2181BSZ-133 IC DSP CONTROLLER 16BIT 128PQFP
VE-B12-CW-B1 CONVERTER MOD DC/DC 15V 100W
VE-21Y-CX-F3 CONVERTER MOD DC/DC 3.3V 49.5W
TAP106J016SRW CAP TANT 10UF 16V 5% RADIAL
相關代理商/技術參數
參數描述
ADSP-2189NBSTZ-3202 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2189NKCA-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:32K PM/48K DM RAM,16-BIT,80 MIPS, 1.8V - Bulk
ADSP-2189NKCAZ-320 功能描述:IC DSP 16BIT 80MHZ 144CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤
ADSP-2189NKCAZ-3202 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2189NKST-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:32K PM/48K DM RAM,16-BIT, 80 MIPS, 1.8V - Bulk 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT