• <samp id="v9bx6"></samp>
  • 參數資料
    型號: ADT7518
    廠商: Analog Devices, Inc.
    元件分類: 溫度/濕度傳感器
    英文描述: SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
    中文描述: SPI/I2C兼容,溫度傳感器,4通道ADC和四路電壓輸出DAC
    文件頁數: 36/40頁
    文件大?。?/td> 1217K
    代理商: ADT7518
    ADT7518
    Rev. A | Page 36 of 40
    0
    1
    R/W
    SCL
    SDA
    FRAME 1
    SERIAL BUS ADDRESS BYTE
    FRAME 2
    ADDRESS POINTER REGISTER BYTE
    ACK. BY
    ADT7518
    ACK. BY
    ADT7518
    STOP BY
    MASTER
    START BY
    MASTER
    0
    0
    1
    A2
    A1
    A
    P7
    P6
    P5
    P4
    P3
    P2
    P1
    P0
    9
    1
    9
    1
    0
    Figure 56. I
    2
    C—Writing to the Address Pointer Register to Select a Register for a Subsequent Read Operation
    FRAME 1
    SERIAL BUS ADDRESS BYTE
    FRAME 2
    ADDRESS POINTER REGISTER BYTE
    ACK. BY
    ADT7518
    ACK. BY
    ADT7518
    STOP BY
    MASTER
    FRAME 3
    DATA BYTE
    SDA (CONTINUED)
    SCL (CONTINUED)
    SCL
    SDA
    START BY
    MASTER
    1
    0
    0
    1
    A2
    A1
    A0
    P7
    P6
    P5
    P4
    P3
    P2
    P1
    P0
    9
    D7
    D6
    D5
    D4
    D3
    D2
    D1
    D0
    R/W
    1
    9
    1
    9
    1
    0
    ACK. BY
    ADT7518
    Figure 57. I
    2
    C—Writing to the Address Pointer Register Followed by a Single Byte of Data to the Selected Register
    1
    SDA
    START BY
    MASTER
    STOP BY
    MASTER
    NO ACK. BY
    MASTER
    ACK. BY
    ADT7518
    SCL
    9
    0
    0
    1
    A2
    A1
    A0
    R/W
    D7
    D6
    D5
    D4
    D3
    D2
    D1
    D0
    FRAME 1
    SERIAL BUS ADDRESS BYTE
    FRAME 2
    SINGLE DATA BYTE FROM ADT7518
    1
    9
    1
    0
    Figure 58. I
    2
    C—Reading a Single Byte of Data from a Selected Register
    Write Operation
    Figure 59 shows the timing diagram for a write operation to the
    ADT7518. Data is clocked into the registers on the rising edge
    of SCLK. When the CS line is high, the DIN and DOUT lines
    are in three-state mode. Only when the CS goes from a high to a
    low does the part accept any data on the DIN line. In SPI mode,
    the address pointer register is capable of autoincrementing to
    the next register in the register map without having to load the
    address pointer register each time. In Figure 59, the register
    address portion gives the first register that will be written to.
    Subsequent data bytes will be written into sequential writable
    registers. Thus, after each data byte has been written into a
    register, the address pointer register autoincrements its value to
    the next available register. The address pointer register will
    autoincrement from 00h to 3Fh and will loop back to start again
    at 00h when it reaches 3Fh.
    Read Operation
    Figure 60 to Figure 62 show the timing diagrams necessary to
    accomplish correct read operations. To read back from a reg-
    ister, first write to the address pointer register with the address
    of the register to be read from. This operation is shown in
    Figure 60. Figure 61 shows the procedure for reading back a
    single byte of data. The read command is first sent to the part
    during the first eight clock cycles. During the following eight
    clock cycles, the data contained in the register selected by the
    address pointer register is output onto the D
    OUT
    line. Data is
    output onto the D
    OUT
    line on the falling edge of SCLK. Figure 62
    shows the procedure when reading data from two sequential
    registers. Multiple data reads are possible in the SPI interface
    mode as the address pointer register is autoincremental. The
    address pointer register will autoincrement from 00h to 3Fh and
    will loop back to start again at 00h when it reaches 3Fh.
    相關PDF資料
    PDF描述
    ADT7518ARQ SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
    ADT7518ARQ-REEL SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
    ADT7518ARQ-REEL7 SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
    ADT7518ARQZ SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
    ADT7518ARQZ-REEL SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
    相關代理商/技術參數
    參數描述
    ADT7518ARQ 制造商:Rochester Electronics LLC 功能描述:DTS,8-BIT QUAD DAC,4 ANALOG INPUTS I.C. - Bulk 制造商:Analog Devices 功能描述:
    ADT7518ARQ-REEL 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R 制造商:Rochester Electronics LLC 功能描述:DTS,8-BIT QUAD DAC,4 ANALOG INPUTS I.C. - Tape and Reel
    ADT7518ARQ-REEL7 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R 制造商:Analog Devices 功能描述:TEMP SENSOR ANLG 4-WIRE/SPI 16QSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:DTS,8-BIT QUAD DAC,4 ANALOG INPUTS I.C. - Tape and Reel
    ADT7518ARQ-U3 制造商:Analog Devices 功能描述:- Bulk
    ADT7518ARQZ 功能描述:IC SENSOR TEMP QD ADC/DAC 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C,外部傳感器 精確度:±2°C 本地(最大),±3°C 遠程(最大) 拓撲:ADC(三角積分型),比較器,寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND