- 您現在的位置：買賣IC網 > PDF目錄379658 > AG1160-48 (Electronic Theatre Controls, Inc.) 5V RINGING SLIC PDF資料下載
參數資料
| 型號： | AG1160-48 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 5V RINGING SLIC |
| 中文描述： | 5V的振鈴用戶接口 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 161K |
| 代理商： | AG1160-48 |
V1.8 October 2006
Data Sheet
surge resistor (25R typically). Alternatively a Teccor
F1250T or F0500T fuse may be used without a surge
resistor.
For ITU-T K20 power cross protection, a PTC
thermistor (eg. type JH330L) of 30R is suitable. The
lightning protection is provided by steering diodes
connected to 0V and upgrading D1 to a Tranzorb
device (Motorola or STM 1.5KE82A). For lightning and
power cross protection, D1 should be upgraded further
(General Semiconductor or Semitron 5KP75). Just one
Tranzorb is needed per linecard.
5.0 Approvals.
It can be seen from the Electrical Characteristics given
on subsequent pages that the SLIC has been designed
to meet the equipment standards of as many major
public telephone authorities as possible.
It is the responsibility of the equipment design authority
to ensure that their system meets the requirements of
the relevant regulatory bodies. Every effort is made to
ensure that Silver Telecom products are compliant with
the latest standards.
Ag1160
5V RINGING SLIC
Silver Telecom 2006
Page 7
6.0 A Typical Application.
The Ag1160 has been designed to interface to any
Codec and is shown in a typical application in Figure 5.
The Codec which has been chosen to illustrate the use
of the Ag1160 is the Motorola MC14LC5480.
The status outputs from the SLIC are passed to the
micro-controller. These signals can then be processed
as necessary by the system software.
The audio signals which are on the 4 wire side of the
connection are coupled by 100nF capacitors to avoid
d.c. level problems between the two devices.
The Ag1160 provides for a 2 wire impedance and a
network balance impedance of 600
. For other
impedances a DSP codec can be used which can be
programmed using applications information available
from the codec manufacturer. The necessary transfer
function parameters for the Ag1160 are available from
Silver Telecom.
RM
SHK
PD
TIP
RING
GND
PWR
+5V
PWR
+5V
A
F/R
V
OUT
IN
PGND
D5
D2
D3
D4
100nF
220uF
10V
0V
PI
VAG
TI+
TI-
PO+
Mu
/a
Vss
FST
DT
BCLKT
MCLK
PDI
BCLKR
DR
Vdd
FSR
TG
RO+
PO-
8KhZ
PCM OUT
2MhZ
to MCU
+5V
100uF
6.3V
100nF
100nF
TIP
RING
Ag1160
CAP
220nF
RO-
0.1u
PCM IN
5v or 0v
Protection is for on-premise applications
Ag1160 is internally programmed for 600R
D1 = BZT03C82 (only 1 needed per linecard)
D2 - D5 = 1N4004
+5V
(Motorola)
MC14LC5480
D1
100nF
+
+5V
+
GND
A
10R
Codec is shown for illustration purposes
l The Ag1160 will work with any codec.
+5V
+5V
PGND
LO
Figure 5: Typical On-Premise Application
.
相關PDF資料 |
PDF描述 |
|---|---|
| AG1160A | 5V RINGING SLIC |
| AG1160A-48 | 5V RINGING SLIC |
| AG1170 | +5V / +3.3V Low Power Ringing SLIC |
| AG1170-D3 | +5V / +3.3V Low Power Ringing SLIC |
| AG1170-D5 | +5V / +3.3V Low Power Ringing SLIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AG1160A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V RINGING SLIC |
| AG1160A-48 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V RINGING SLIC |
| AG11692 | 制造商:Molex 功能描述:LOCKNUT PG9 *52003500* |
| AG1170 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:+5V / +3.3V Low Power Ringing SLIC |
| AG1170-D3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:+5V / +3.3V Low Power Ringing SLIC |
發布緊急采購，3分鐘左右您將得到回復。