3-2 Revision 17 interface is neither used nor planned for use, the VJTAG pin together with the TRST pin could be tied to GND. It " />
參數資料
型號: AGLN060V2-ZVQG100
廠商: Microsemi SoC
文件頁數: 9/150頁
文件大小: 0K
描述: IC FPGA NANO 1KB 60K 100VQFP
標準包裝: 90
系列: IGLOO nano
邏輯元件/單元數: 1536
RAM 位總計: 18432
輸入/輸出數: 71
門數: 60000
電源電壓: 1.14 V ~ 1.575 V
安裝類型: 表面貼裝
工作溫度: -20°C ~ 70°C
封裝/外殼: 100-TQFP
供應商設備封裝: 100-VQFP(14x14)
Pin Descriptions
3-2
Revision 17
interface is neither used nor planned for use, the VJTAG pin together with the TRST pin could be tied to
GND. It should be noted that VCC is required to be powered for JTAG operation; VJTAG alone is
insufficient. If a device is in a JTAG chain of interconnected boards, the board containing the device can
be powered down, provided both VJTAG and VCC to the part remain powered; otherwise, JTAG signals
will not be able to transition the device, even in bypass mode.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
VPUMP
Programming Supply Voltage
IGLOO nano devices support single-voltage ISP of the configuration flash and FlashROM. For
programming, VPUMP should be 3.3 V nominal. During normal device operation, VPUMP can be left
floating or can be tied (pulled up) to any voltage between 0 V and the VPUMP maximum. Programming
power supply voltage (VPUMP) range is listed in the datasheet.
When the VPUMP pin is tied to ground, it will shut off the charge pump circuitry, resulting in no sources of
oscillation from the charge pump circuitry.
For proper programming, 0.01 F and 0.33 F capacitors (both rated at 16 V) are to be connected in
parallel across VPUMP and GND, and positioned as close to the FPGA pins as possible.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
User Pins
I/O
User Input/Output
The I/O pin functions as an input, output, tristate, or bidirectional buffer. Input and output signal levels are
compatible with the I/O standard selected.
During programming, I/Os become tristated and weakly pulled up to VCCI. With VCCI, VMV, and VCC
supplies continuously powered up, when the device transitions from programming to operating mode, the
I/Os are instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
Output buffer is disabled (with tristate value of high impedance)
Input buffer is disabled (with tristate value of high impedance)
Weak pull-up is programmed
GL
Globals
GL I/Os have access to certain clock conditioning circuitry (and the PLL) and/or have direct access to the
global network (spines). Additionally, the global I/Os can be used as regular I/Os, since they have
identical capabilities. Unused GL pins are configured as inputs with pull-up resistors.
See more detailed descriptions of global I/O connectivity in the "Clock Conditioning Circuits in IGLOO
and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide. All inputs labeled
GC/GF are direct inputs into the quadrant clocks. For example, if GAA0 is used for an input, GAA1 and
GAA2 are no longer available for input to the quadrant globals. All inputs labeled GC/GF are direct inputs
into the chip-level globals, and the rest are connected to the quadrant globals. The inputs to the global
network are multiplexed, and only one input can be used as a global input.
Refer to the "I/O Structures in nano Devices" chapter of the IGLOO nano FPGA Fabric User’s Guide for
an explanation of the naming of global pins.
FF
Flash*Freeze Mode Activation Pin
Flash*Freeze is available on IGLOO nano devices. The FF pin is a dedicated input pin used to enter and
exit Flash*Freeze mode. The FF pin is active low, has the same characteristics as a single-ended I/O,
and must meet the maximum rise and fall times. When Flash*Freeze mode is not used in the design, the
FF pin is available as a regular I/O.
When Flash*Freeze mode is used, the FF pin must not be left floating to avoid accidentally entering
Flash*Freeze mode. While in Flash*Freeze mode, the Flash*Freeze pin should be constantly asserted.
The Flash*Freeze pin can be used with any single-ended I/O standard supported by the I/O bank in
which the pin is located, and input signal levels compatible with the I/O standard selected. The FF pin
相關PDF資料
PDF描述
BR24T64FJ-WE2 IC EEPROM I2C 64K 400KHZ 8-SOP
AGLN060V2-ZVQ100 IC FPGA NANO 1KB 60K 100VQFP
AGL060V2-VQ100 IC FPGA 1KB FLASH 60K 100-VQFP
EP4CE6E22C9LN IC CYCLONE IV FPGA 6K 144EQFP
BR24T64FVT-WE2 IC EEPROM I2C 64K 400KHZ 8-TSSOP
相關代理商/技術參數
參數描述
AGLN060V2-ZVQG100I 功能描述:IC FPGA NANO 1KB 60K 100VQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA,CSBGA 供應商設備封裝:289-CSP(14x14)
AGLN060V5-CSG81 功能描述:IC FPGA 60K 1.5V CSP81 RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:60 系列:XP LAB/CLB數:- 邏輯元件/單元數:10000 RAM 位總計:221184 輸入/輸出數:244 門數:- 電源電壓:1.71 V ~ 3.465 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:388-BBGA 供應商設備封裝:388-FPBGA(23x23) 其它名稱:220-1241
AGLN060V5-CSG81I 功能描述:IC FPGA NANO 1KB 60K 81-CSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA,CSBGA 供應商設備封裝:289-CSP(14x14)
AGLN060V5-VQ100 功能描述:IC FPGA NANO 1KB 60K 100VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA,CSBGA 供應商設備封裝:289-CSP(14x14)
AGLN060V5-VQ100I 功能描述:IC FPGA NANO 1KB 60K 100VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA,CSBGA 供應商設備封裝:289-CSP(14x14)