- 您現在的位置：買賣IC網 > PDF目錄166204 > ALD1704SA (Advanced Linear Devices, Inc.) RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | ALD1704SA |
| 廠商： | Advanced Linear Devices, Inc. |
| 英文描述： | RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| 中文描述： | 軌對軌CMOS運算放大器 |
| 文件頁數： | 4/6頁 |
| 文件大小： | 47K |
| 代理商： | ALD1704SA |
ALD1704A/ALD1704B
Advanced Linear Devices
4
ALD1704/ALD1704G
TYPICAL PERFORMANCE CHARACTERISTICS
Design & Operating Notes:
1. The ALD1704 CMOS operational amplifier uses a 3 gain stage
architecture and an improved frequency compensation scheme to
achieve large voltage gain, high output driving capability, and better
frequency stability. The ALD1704 is internally compensated for unity
gain stability using a novel scheme that produces a clean single pole
roll off in the gain characteristics while providing for more than 70
degrees of phase margin at the unity gain frequency. A unity gain
buffer using the ALD1704 will typically drive 400pF of external load
capacitance without stability problems. In the inverting unity gain
configuration, it can drive up to 800pF of load capacitance. Compared
to other CMOS operational amplifiers, the ALD1704 has shown itself
to be more resistant to parasitic oscillations.
2. The ALD1704 has complementary p-channel and n-channel input
differential stages connected in parallel to accomplish rail to rail input
common mode voltage range. This means that with the ranges of
common mode input voltage close to the power supplies, one of the
two differential stages is switched off internally. To maintain compat-
ibility with other operational amplifiers, this switching point has been
selected to be about 1.5V above the negative supply voltage. Since
offset voltage trimming on the ALD1704 is made when the input
voltage is symmetrical to the supply voltages, this internal switching
does not affect a large variety of applications such as an inverting
amplifier or non-inverting amplifier with a gain larger than 2 (10V
operation), where the common mode voltage does not make excur-
sions below this switching point.
3. The input bias and offset currents are essentially input protection diode
reverse bias leakage currents, and are typically less than 1pA at room
temperature. This low input bias current assures that the analog signal
from the source will not be distorted by input bias currents. For applica-
tions where source impedance is very high, it may be necessary to limit
noise and hum pickup through proper shielding.
4. The output stage consists of symmetrical class AB complementary
output drivers, capable of driving a low resistance load with up to 10mA
source current and 10mA sink current. The output voltage swing is
limited by the drain to source on-resistance of the output transistors as
determined by the bias circuitry, and the value of the load resistor. When
connected in the voltage follower configuration, the oscillation resistant
feature, combined with the rail-to-rail input and output feature, makes
the ALD1704 an effective analog signal buffer for medium to high source
impedance sensors, transducers, and other circuit networks.
5. The ALD1704 operational amplifier has been designed to provide full
static discharge protection. Internally, the design has been carefully
implemented to minimize latch up. However, care must be exercised
when handling the device to avoid strong static fields that may degrade
a diode junction, causing increased input leakage currents. In using the
operational amplifier, the user is advised to power up the circuit before,
or simultaneously with, any input voltages applied and to limit input
voltages to not exceed 0.3V of the power supply voltage levels.
INPUT BIAS CURRENT AS A FUNCTION
OF AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (
°C)
1000
100
10
0.1
1.0
INPUT
BIAS
CURRENT
(pA)
100
-25
0
75
125
50
25
-50
VS = ±5.0V
10000
OPEN LOOP VOLTAGE GAIN AS A FUNCTION
OF SUPPLY VOLTAGE AND TEMPERATURE
SUPPLY VOLTAGE (V)
1000
100
10
1
OPEN
LOOP
VOLTAGE
GAIN
(V/mV)
0
±2
±4
±6
RL= 10K
RL= 5K
} -55
°C
} +25
°C
} +125
°C
±8
SUPPLY CURRENT AS A FUNCTION
OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
5
4
3
2
1
0
SUPPLY
CURRENT
(mA)
0
±1
±2
±3
±4
±5
±6
+125
°C
+80
°C
+25
°C
TA = -55°C
-25
°C
INPUTS GROUNDED
OUTPUT UNLOADED
COMMON MODE INPUT VOLTAGE RANGE
AS A FUNCTION OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
COMMON
MODE
INPUT
VOLTAGE
RANGE
(V)
±7
±6
±5
±4
±3
±2
±3
±4
±5
±6
±7
TA = 25°C
相關PDF資料 |
PDF描述 |
|---|---|
| ALD1704BSA | RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD1704GPA | RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD1706BPA | ULTRA MICROPOWER RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD1722EDA | EPAD⑩ OPERATIONAL AMPLIFIER |
| ALD1726EDA | EPAD⑩ ULTRA MICROPOWER OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ALD1704SAL | 功能描述:運算放大器 - 運放 Hi Slew Rate R-to-R RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ALD1704Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| ALD1706 | 制造商:ALD 制造商全稱:Advanced Linear Devices 功能描述:ULTRA MICROPOWER RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD1706A | 制造商:ALD 制造商全稱:Advanced Linear Devices 功能描述:ULTRA MICROPOWER RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD1706A_10 | 制造商:ALD 制造商全稱:Advanced Linear Devices 功能描述:ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。