- 您現在的位置：買賣IC網 > PDF目錄366393 > AM28F512-200JI (ADVANCED MICRO DEVICES INC) Dual D-type pos.-edge-triggered flip-flops with preset and clear 14-SSOP 0 to 70 PDF資料下載
參數資料
| 型號： | AM28F512-200JI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | Dual D-type pos.-edge-triggered flip-flops with preset and clear 14-SSOP 0 to 70 |
| 中文描述： | 64K X 8 FLASH 12V PROM, 200 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 9/35頁 |
| 文件大小： | 484K |
| 代理商： | AM28F512-200JI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Am28F512
9
READ ONLY MODE
When V
PP
is less than V
CC
+ 2 V, the command register
is inactive. The device can either read array or autose-
lect data, or be standby mode.
Read
The device functions as a read only memory when V
PP
< V
CC
+ 2 V.
The device has two control functions. Both
must be satisfied in order to output data. CE# controls
power to the device. This pin should be used for spe-
cific device selection. OE# controls the device outputs
and should be used to gate data to the output pins if a
device is selected.
Address access time t
ACC
is equal to the delay from
stable addresses to valid output data. The chip enable
access time t
CE
is the delay from stable addresses and
stable CE# to valid data at the output pins. The output
enable access time is the delay from the falling edge of
OE# to valid data at the output pins (assuming the ad-
dresses have been stable at least t
ACC
–t
OE
).
Standby Mode
The device has two standby modes. The CMOS
standby mode (CE# input held at V
CC
±
0.5 V), con-
sumes less than 100 μA of current. TTL standby mode
(CE# is held at V
IH
) reduces the current requirements
to less than 1mA. When in the standby mode the out-
puts are in a high impedance state, independent of the
OE# input.
If the device is deselected during erasure, program-
ming, or program/erase verification, the device will
draw active current until the operation is terminated.
Output Disable
Output from the device is disabled when OE# is at a
logic high level. When disabled, output pins are in a
high impedance state.
Auto Select
Flash memories can be programmed in-system or in a
standard PROM programmer. The device may be sol-
dered to the circuit board upon receipt of shipment and
programmed in-system. Alternatively, the device may
initially be programmed in a PROM programmer prior
to soldering the device to the board.
The Auto select mode allows the reading out of a binary
code from the device that will identify its manufacturer
and type. This mode is intended for the purpose
of automatically matching the device to be pro-
grammed with its corresponding programming algo-
rithm. This mode is functional over the entire
temperature range of the device.
Programming In A PROM Programmer
To activate this mode, the programming equipment
must force V
ID
(11.5 V to 13.0 V) on address A9. Two
identifier bytes may then be sequenced from the device
outputs by toggling address A
0
from V
IL
to V
IH
. All other
address lines must be held at V
IL
, and V
PP
must
be
less than or equal to V
CC
+ 2.0 V while using this Auto
select mode. Byte 0 (A0 = V
IL
) represents the manufac-
turer code and byte 1 (A0 = V
IH
) the device identifier
code. For the device these two bytes are given in Table
2 below. All identifiers for manufacturer and device
codes will exhibit odd parity with the MSB (DQ7) de-
fined as the parity bit.
Table 2.
Am28F512 Auto Select Code
Type
A0
Code (HEX)
Manufacturer Code
V
IL
01
Device Code
V
IH
25
相關PDF資料 |
PDF描述 |
|---|---|
| AM28F512-200JIB | 512 Kilobit (64 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F512-200PC | Dual D-type pos.-edge-triggered flip-flops with preset and clear 14-SOIC 0 to 70 |
| AM28F512-200PCB | 512 Kilobit (64 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F512-200PE | Dual D-type pos.-edge-triggered flip-flops with preset and clear 14-SOIC 0 to 70 |
| AM28F512-200PEB | Dual D-type pos.-edge-triggered flip-flops with preset and clear 14-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM28F512-90JC | 制造商:Advanced Micro Devices 功能描述: 制造商:Advanced Micro Devices 功能描述:64K X 8 FLASH 12V PROM, 90 ns, PQCC32 |
| AM29 | 制造商:Distributed By MCM 功能描述:REFRIGERATR DOOR GASKET DIRECT |
| AM290 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| AM29000 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Am29000 and Am29005? Processor Data Sheet |
| AM29000-16/BYC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。