- 您現在的位置：買賣IC網 > PDF目錄223346 > AM29BDD160GB65APBI (ADVANCED MICRO DEVICES INC) 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory PDF資料下載
參數資料
| 型號： | AM29BDD160GB65APBI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| 中文描述： | 512K X 32 FLASH 2.7V PROM, 67 ns, PBGA80 |
| 封裝： | 13 X 11 MM, 1 MM PITCH, BGA-80 |
| 文件頁數： | 31/80頁 |
| 文件大?。?/td> | 3476K |
| 代理商： | AM29BDD160GB65APBI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Am29BDD160G
35
device is in Unlock Bypass mode and during normal
read/reset operating mode.
In this mode, the write protection function is by-
passed unless the PPB Lock Bit = 1.
The Accelerated Program command is not permitted
if the SecSi sector is enabled.
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to pro-
gram words to the device faster than using the
standard program command sequence. The unlock
bypass command sequence is initiated by first writ-
ing two unlock cycles. This is followed by a third
write cycle containing the unlock bypass command,
20h. The device then enters the unlock bypass
mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this
mode. The first cycle in this sequence contains the
unlock bypass program command, A0h; the second
cycle contains the program address and data. Addi-
tional data is programmed in the same manner. This
mode dispenses with the initial two unlock cycles re-
quired in the standard program command sequence,
resulting in faster total programming time. Tables 18
and 20 show the requirements for the command se-
quence.
During the unlock bypass mode, only the Unlock By-
pass Program and Unlock Bypass Reset commands
are valid. To exit the unlock bypass mode, the sys-
tem must issue the two-cycle unlock bypass reset
command sequence. The first cycle must contain the
data 90h; the second cycle the data 00h. Addresses
are don’t care for both cycles. The device then re-
turns to reading array data.
Figure 4 illustrates the algorithm for the program op-
eration. See the Erase/Program Operations table in
AC Characteristics for parameters, and to Figure 22
for timing diagrams.
Note:See Tables 18 and 20 for program command
sequence.
Figure 4. Program Operation
Unlock Bypass Entry Command
The Unlock Bypass command, once issued, is used to
bypass the “unlock” sequence for program, chip
erase, and CFI commands. This feature permits slow
PROM programmers to significantly improve pro-
gramming/erase throughput since the command
sequence often requires microseconds to execute a
single write operation. Therefore, once the Unlock
Bypass command is issued, only the two-cycle pro-
gram and erase bypass commands are required. The
Unlock Bypass Command is ignored if the SecSi sec-
tor is enabled. To return back to normal operation,
the Unlock Bypass Reset Command must be issued.
The following four sections describe the commands
that may be executed within the unlock bypass
mode.
Unlock Bypass Program Command
The Unlock Bypass Program command is a two-cycle
command that consists of the actual program com-
mand ( A0h) a n d the program a ddress /data
combination. This command does not require the
two-cycle “unlock” sequence since the Unlock Bypass
command was previously issued. As with the stan-
dard program command, multiple Unlock Bypass
Program commands can be issued once the Unlock
Bypass command is issued.
To return back to standard read operations, the Un-
lock Bypass Reset command must be issued.
The Unlock Bypass Program Command is ignored if
the SecSi sector is enabled.
Start
相關PDF資料 |
PDF描述 |
|---|---|
| AM29BDD160GT54DKE | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT54DKF | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT54DKI | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT54DKK | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT54DPBE | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29BDS128HE9VKI | 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel/Serial 1.8V 128M-Bit 8M x 16 50ns 80-Pin FBGA |
| AM29BDS643GT5KVAI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays |
| AM29BL802CB-65RZET | 制造商:Spansion 功能描述: |
| AM29C01WW WAF | 制造商:Advanced Micro Devices 功能描述: |
| AM29C10API | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。