參數資料
型號： AM29F016D-150E4I
廠商： ADVANCED MICRO DEVICES INC
元件分類： PROM
英文描述： 16 Megabit (2 M x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
中文描述： 2M X 8 FLASH 5V PROM, 150 ns, PDSO40
封裝： MO-142CD, TSOP-40
文件頁數： 11/45頁
文件大小： 1145K
代理商： AM29F016D-150E4I
10
Am29F016D
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and I
CC
read specifications apply. Refer to “Write Operation
Status” for more information, and to each AC Charac-
teristics section for timing diagrams.
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when CE#
and RESET# pins are both held at V
CC
± 0.5 V. (Note
that this is a more restricted voltage range than V
IH
.)
The device enters the TTL standby mode when CE#
and RESET# pins are both held at V
IH
. The device re-
quires standard access time (t
CE
) for read access when
the device is in either of these standby modes, before it
is ready to read data.
The device also enters the standby mode when the RE-
SET# pin is driven low. Refer to the next section, “RE-
SET#: Hardware Reset Pin”.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
In the DC Characteristics tables, I
CC3
represents the
standby current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the system
drives the RESET# pin low for at least a period of t
RP
,
the device
immediately terminates
any operation in
progress, tristates all data output pins, and ignores all
read/write attempts for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at V
IL
, the device enters
the TTL standby mode; if RESET# is held at V
SS
±
0.5 V, the device enters the CMOS standby mode.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
If RESET# is asserted during a program or erase oper-
ation, the RY/BY# pin remains a “0” (busy) until the in-
ternal reset operation is complete, which requires a
time of t
READY
(during Embedded Algorithms). The
system can thus monitor RY/BY# to determine whether
the reset operation is complete. If RESET# is asserted
when a program or erase operation is not executing
(RY/BY# pin is “1”), the reset operation is completed
within a time of t
READY
(not during Embedded Algo-
rithms). The system can read data t
RH
after the RE-
SET# pin returns to V
IH
.
Refer to the AC Characteristics tables for RESET# pa-
rameters and timing diagram.
Output Disable Mode
When the OE# input is at V
IH
, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
相關PDF資料
PDF描述
AM29F016D-150EC LM136-2.5/LM236-2.5/LM336-2.5V Reference Diode; Package: TO-92; No of Pins: 3; Qty per Container: 1800; Container: Box
Am29F016D-150ECB LM136-5.0/LM236-5.0/LM336-5.0 5.0V Reference Diode; Package: TO-92; No of Pins: 3; Qty per Container: 1800; Container: Box
AM29F016D-150EE LM3370 Dual Synchronous Step-Down DC-DC Converter with Dynamic Voltage Scaling Function; Package: LLP; No of Pins: 16; Qty per Container: 1000; Container: Reel
Am29F016D-150EEB LM3370 Dual Synchronous Step-Down DC-DC Converter with Dynamic Voltage Scaling Function; Package: LLP; No of Pins: 16; Qty per Container: 1000; Container: Reel
AM29F016D-150EI 16 Megabit (2 M x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
相關代理商/技術參數
參數描述
AM29F016D-150EC 制造商:Spansion 功能描述:16M (2MX8) 5V, UNIFORM SECTOR, TSOP48, COM - Trays
AM29F016D-70E4D 制造商:SOCO 功能描述:
AM29F016D-70E4F 功能描述:閃存 16M (2MX8) 70ns 5v Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
AM29F016D-70EF 功能描述:閃存 16M (2MX8) 70ns 5v Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
AM29F016D-70EI 制造商:Spansion 功能描述:NOR Flash Parallel 5V 16Mbit 2M x 8bit 70ns 48-Pin TSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*