- 您現在的位置：買賣IC網 > PDF目錄366418 > AM29F016D-90FI (ADVANCED MICRO DEVICES INC) 16 Megabit (2 M x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29F016D-90FI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 16 Megabit (2 M x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| 中文描述： | 2M X 8 FLASH 5V PROM, 90 ns, PDSO48 |
| 封裝： | REVERSE, MO-142DD, TSOP-48 |
| 文件頁數： | 18/45頁 |
| 文件大?。?/td> | 1145K |
| 代理商： | AM29F016D-90FI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
Am29F016D
17
Any commands written to the device during the Em-
bedded Program Algorithm are ignored. Note that a
hardware reset
immediately terminates the program-
ming operation. The program command sequence
should be reinitiated once the device has reset to read-
ing array data, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries.
A bit cannot be programmed
from a “0” back to a “1”.
Attempting to do so may halt
the operation and set DQ5 to “1”, or cause the Data#
Polling algorithm to indicate the operation was suc-
cessful. However, a succeeding read will show that the
data is still “0”. Only erase operations can convert a “0”
to a “1”.
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to pro-
gram bytes or words to the device faster than using the
standard program command sequence. The unlock by-
pass command sequence is initiated by first writing two
unlock cycles. This is followed by a third write cycle
containing the unlock bypass command, 20h. The de-
vice then enters the unlock bypass mode. A two-cycle
unlock bypass program command sequence is all that
is required to program in this mode. The first cycle in
this sequence contains the unlock bypass program
command, A0h; the second cycle contains the program
address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial
two unlock cycles required in the standard program
command sequence, resulting in faster total program-
ming time. Table 9 shows the requirements for the com-
mand sequence.
During the unlock bypass mode, only the Unlock By-
pass Program and Unlock Bypass Reset commands
are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset com-
mand sequence. The first cycle must contain the data
90h; the second cycle the data 00h. Addresses are
don’t care for both cycles. The device then returns to
reading array data.
Note:
See the appropriate Command Definitions table for program
command sequence.
Figure 2.
Program Operation
Chip Erase Command Sequence
Chip erase is a six-bus-cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm. The device does
not
require the system to
preprogram prior to erase. The Embedded Erase algo-
rithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any con-
trols or timings during these operations. The Command
Definitions table shows the address and data require-
ments for the chip erase command sequence.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F016D-90SC | 16 Megabit (2 M x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| Am29F016D-90SCB | 16 Megabit (2 M x 8-Bit)CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F016D-90SE | 16Megabit（2M*8-bit)的CMOS 5.0 volt-only，uniform sector flash memory |
| Am29F016D-90SEB | 16 Megabit (2 M x 8-Bit)CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F016D-90SI | 16 Megabit（2M*8-bit）CMOS 5.0 volt-only，uniform sector flash memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F016D-90SD | 制造商:Spansion 功能描述:IC 16M (2M X 8-BIT)5V SECTOR |
| AM29F016D-90SF | 功能描述:閃存 16M (2MX8) 90ns 5v Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AM29F016D-90SF\T | 功能描述:閃存 16M (2MX8) 90ns 5v Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AM29F016D-90SI | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 16Mbit 2M x 8bit 90ns 44-Pin SO |
| AM29F016D-90SI\T | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 16Mbit 2M x 8bit 90ns 44-Pin SOIC T/R |
發布緊急采購，3分鐘左右您將得到回復。