- 您現在的位置：買賣IC網 > PDF目錄366423 > AM29F040-90JEB (ADVANCED MICRO DEVICES INC) 4 Megabit (524,288 x 8-Bit) CMOS 5.0 Volt-only, Sector Erase Flash Memory PDF資料下載
參數資料
| 型號： | AM29F040-90JEB |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 4 Megabit (524,288 x 8-Bit) CMOS 5.0 Volt-only, Sector Erase Flash Memory |
| 中文描述： | 512K X 8 FLASH 5V PROM, 90 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 7/33頁 |
| 文件大?。?/td> | 190K |
| 代理商： | AM29F040-90JEB |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Am29F040
7
Table 1.
Am29F040 User Bus Operations
Legend:
L = Logic 0, H = Logic 1, X = Don’t Care. See DC Characteristics for voltage levels.
Notes:
1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Tables 2 and 4.
2. Refer to Table 3 for valid PD (Program Data) during a write operation.
3. Refer to the section on Sector Protection.
4. WE can be V
IL
if OE is V
IL
, OE at V
IH
initiates the write operations.
Read Mode
The Am29F040 has two control functions which must
be satisfied in order to obtain data at the outputs. CE is
the power control and should be used for device selec-
tion. OE is the output control and should be used to
gate data to the output pins if a device is selected.
Address access time (t
stable addresses to valid output data. The chip enable
access time (t
CE
) is the delay from stable addresses and
stable CE to valid data at the output pins. The output en-
able access time is the delay from the falling edge of OE
to valid data at the output pins (assuming the addresses
have been stable for at least t
Standby Mode
The Am29F040 has two standby modes, a CMOS
standby mode (CE input held at V
current consumed is less than 5
mode (CE is held at V
IH
) when the current required is
reduced to approximately 1 mA. In the standby mode
the outputs are in a high impedance state, independent
of the OE input.
ACC
) is equal to the delay from
ACC
–t
OE
time).
CC
μ
A; and a TTL standby
±
0.5 V), when the
If the device is deselected during erasure or program-
ming, the device will draw active current until the
operation is completed.
Output Disable
With the OE input at a logic high level (V
the device is disabled. This will cause the output pins to
be in a high impedance state.
Autoselect
The autoselect mode allows the reading out of a binary
code from the device and will identify its manufacturer
and type. This mode is intended for use by programming
equipment for the purpose of automatically matching the
device to be programmed with its corresponding pro-
gramming algorithm. This mode is functional over the
entire temperature range of the device.
IH
), output from
To activate this mode, the programming equipment
must force V
ID
(11.5 V to 12.5 V) on address pin A9.
Two identifier bytes may then be sequenced from the
device outputs by toggling address A0 from V
All addresses are don’t cares except A0, A1, and A6.
IL
to V
IH
.
The manufacturer and device codes may also be read
via the command register, for instances when the
Am29F040 is erased or programmed in a system with-
out access to high voltage on the A9 pin. The command
sequence is illustrated in Table 4 (refer to Autoselect
Command section).
Byte 0 (A0 = V
(AMD = 01H) and byte 1 (A0 = V
code (Am29F040 = A4H). All identifiers for manufac-
turer and device exhibit odd parity with the MSB (DQ7)
defined as the parity bit. See Table 2.
IL
) represents the manufacturer’s code
) the device identifier
IH
Operation
CE
OE
WE
A0
A1
A6
A9
I/O
Autoselect Manufacturer Code (Note 1)
L
L
H
L
L
L
V
ID
Code
Autoselect Device Code (Note 1)
L
L
H
H
L
L
V
ID
Code
Read (Note 4)
L
L
H
A0
A1
A6
A9
RD
Standby
H
X
X
X
X
X
X
HIGH Z
Output Disable
L
H
H
X
X
X
X
HIGH Z
Write
L
H
L
A0
A1
A6
A9
PD (Note 2)
Verify Sector Protect (Note 3)
L
L
H
L
H
L
V
ID
Code
Autoselect Device Unprotect Code
L
L
H
H
H
L
V
ID
Code
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F040B-120ECB | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| Am29F040B-90 | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120JE | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120JEB | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120JI | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F040-90JI- RFB | 制造商:Advanced Micro Devices 功能描述: |
| AM29F040B120EC | 制造商:AMD 功能描述:* |
| AM29F040B-120EC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 512K x 8, 32 Pin, Plastic, TSSOP 制造商:SILICON 功能描述:NOR Flash, 512K x 8, 32 Pin, Plastic, TSSOP |
| AM29F040B-120ED | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K x 8bit 120ns 32-Pin TSOP 制造商:Spansion 功能描述:Flash Memory IC 制造商:Advanced Micro Devices 功能描述:NOR Flash, 512K x 8, 32 Pin, Plastic, TSSOP |
| AM29F040B-120EE | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K x 8bit 120ns 32-Pin TSOP |
發布緊急采購，3分鐘左右您將得到回復。