- 您現在的位置：買賣IC網 > PDF目錄362257 > AM29F200BT-75DGC1 20V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRLR3715ZCPBF with Standard Packaging PDF資料下載
參數資料
| 型號： | AM29F200BT-75DGC1 |
| 英文描述： | 20V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRLR3715ZCPBF with Standard Packaging |
| 中文描述： | EEPROM的 |
| 文件頁數： | 10/39頁 |
| 文件大?。?/td> | 728K |
| 代理商： | AM29F200BT-75DGC1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
10
Am29F002B/Am29F002NB
Table 3.
Am29F002B/Am29F002NB Bottom Boot Block Sector Address Table
Autoselect Mode
The autoselect mode provides manufacturer and
device identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment
to automatically match a device to be programmed with
its corresponding programming algorithm. However,
the autoselect codes can also be accessed in-system
through the command register.
When using programming equipment, the autoselect
mode requires V
ID
on address pin A9. Address pins A6,
A1, and A0 must be as shown in Autoselect Codes
(High Voltage Method) table. In addition, when verifying
sector protection, the sector address must appear on
the appropriate highest order address bits. Refer to the
corresponding Sector Address Tables. The Command
Definitions table shows the remaining address bits that
are don’t care. When all necessary bits have been set
as required, the programming equipment may then
read the corresponding identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in the Command Defini-
tions table. This method does not require V
ID
. See
“Command Definitions” for details on using the autose-
lect mode.
Table 4.
Am29F002B/Am29F002NB Autoselect Codes (High Voltage Method)
L = Logic Low = V
IL
, H = Logic High = V
IH
, SA = Sector Address, X = Don’t care.
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The hard-
ware sector unprotection feature re-enables both
program and erase operations in previously protected
sectors.
Sector
SA0
SA1
SA2
SA3
SA4
SA5
SA6
A17
0
0
0
0
0
1
1
A16
0
0
0
0
1
0
1
A15
0
0
0
1
X
X
X
A14
0
1
1
X
X
X
X
A13
X
0
1
X
X
X
X
Sector Size
(Kbytes)
16
8
8
32
64
64
64
Address Range
(in hexadecimal)
00000h–03FFFh
04000h–05FFFh
06000h–07FFFh
08000h–0FFFFh
10000h–1FFFFh
20000h–2FFFFh
30000h–3FFFFh
Description
CE#
OE#
WE#
A17
to
A13
A12
to
A10
A9
A8
to
A7
A6
A5
to
A2
A1
A0
DQ7
to
DQ0
Manufacturer ID
:
AMD
L
L
H
X
X
V
ID
X
L
X
L
L
01h
Device ID:
Am29F002B/Am29F002NB
(Top Boot Block)
L
L
H
X
X
V
ID
X
L
X
L
H
B0h
L
L
H
Device ID:
Am29F002B/Am29F002NB
(Bottom Boot Block)
L
L
H
X
X
V
ID
X
L
X
L
H
34h
L
L
H
Sector Protection Verification
L
L
H
SA
X
V
ID
X
L
X
H
L
01h
(protected)
00h
(unprotected)
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F200BT-75DGE1 | EEPROM |
| AM29F200BT-75DGI1 | EEPROM |
| AM29F200T-120EI | x8/x16 Flash EEPROM |
| AM29F200T-120FC | x8/x16 Flash EEPROM |
| AM29F200T-120FE | x8/x16 Flash EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F200BT-90SC | 制造商:Advanced Micro Devices 功能描述: |
| AM29F200BT-90SI | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 2Mbit 256K/128K x 8bit/16bit 90ns 44-Pin SO |
| AM29F200BT-90SI\\T | 制造商:Spansion 功能描述:AM29F200BT-90SI\\T - Tape and Reel |
| AM29F200BT-90SI\T | 制造商:Spansion 功能描述:AM29F200BT-90SI\T - Tape and Reel |
| AM29F400AB-120DGC1 | 制造商:Spansion 功能描述:4M FLASH KNOWN GOOD DIE W/ TOP BOOT (COMMERCIAL TEMP) - Gel-pak, waffle pack, wafer, diced wafer on film |
發布緊急采購，3分鐘左右您將得到回復。