參數資料
型號： AM29F200BT-75DGE1
元件分類： EEPROM
英文描述： EEPROM
中文描述： EEPROM的
文件頁數： 15/39頁
文件大?。?/td> 728K
代理商： AM29F200BT-75DGE1
Am29F002B/Am29F002NB
15
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to
interrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure. This command is valid only during the sector
erase operation, including the 50 μs time-out period
during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program algo-
rithm. Writing the Erase Suspend command during the
Sector Erase time-out immediately terminates the
time-out period and suspends the erase operation.
Addresses are “don’t-cares” when writing the Erase
Suspend command.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 μs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately ter-
minates the time-out period and suspends the erase
operation.
After the erase operation has been suspended, the
system can read array data from or program data to
any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Normal
read and write timings and command definitions apply.
Reading at any address within erase-suspended
sectors produces status data on DQ7–DQ0. The
system can use DQ7, or DQ6 and DQ2 together, to
determine if a sector is actively erasing or is erase-sus-
pended. See “Write Operation Status” for information
on these status bits.
After an erase-suspended program operation is com-
plete, the system can once again read array data within
non-suspended sectors. The system can determine
the status of the program operation using the DQ7 or
DQ6 status bits, just as in the standard program oper-
ation. See “Write Operation Status” for more
information.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend
mode. The device allows reading autoselect codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the autoselect mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation. See “Autoselect Command Sequence”
for more information.
The system must write the Erase Resume command
(address bits are “don’t care”) to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another
Erase Suspend command can be written after the
device has resumed erasing.
相關PDF資料
PDF描述
AM29F200BT-75DGI1 EEPROM
AM29F200T-120EI x8/x16 Flash EEPROM
AM29F200T-120FC x8/x16 Flash EEPROM
AM29F200T-120FE x8/x16 Flash EEPROM
AM29F200T-120FEB A 20V Single N-Channel HEXFET Power MOSFET in a DirectFET MP, 59 Amps
相關代理商/技術參數
參數描述
AM29F200BT-90SC 制造商:Advanced Micro Devices 功能描述:
AM29F200BT-90SI 制造商:Spansion 功能描述:NOR Flash Parallel 5V 2Mbit 256K/128K x 8bit/16bit 90ns 44-Pin SO
AM29F200BT-90SI\\T 制造商:Spansion 功能描述:AM29F200BT-90SI\\T - Tape and Reel
AM29F200BT-90SI\T 制造商:Spansion 功能描述:AM29F200BT-90SI\T - Tape and Reel
AM29F400AB-120DGC1 制造商:Spansion 功能描述:4M FLASH KNOWN GOOD DIE W/ TOP BOOT (COMMERCIAL TEMP) - Gel-pak, waffle pack, wafer, diced wafer on film
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*