- 您現在的位置：買賣IC網 > PDF目錄223348 > AM29F400BB-70EC (ADVANCED MICRO DEVICES INC) 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29F400BB-70EC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 256K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| 封裝： | MO-142DD, TSOP-48 |
| 文件頁數： | 7/41頁 |
| 文件大?。?/td> | 919K |
| 代理商： | AM29F400BB-70EC |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Am29F400B
15
be accepted, and erasure may begin. It is recom-
mended that processor interrupts be disabled during
this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector Erase
command is written. If the time between additional
sector erase commands can be assumed to be less
than 50 s, the system need not monitor DQ3. Any
command other than Sec tor Erase or E ras e
Suspend during the time-out period resets the
device to reading array data. The system must
rewrite the command sequence and any additional
sector addresses and commands.
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising
edge of the final WE# pulse in the command sequence.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. Note that a hardware reset during the
sector erase operation immediately terminates the
operation. The Sector Erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure data integrity.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the
status of the erase operation by using DQ7, DQ6, DQ2,
or RY/BY#. (Refer to “The Erase Resume command is
valid only during the Erase Suspend mode.” for infor-
mation on these status bits.)
Figure 3 illustrates the algorithm for the erase opera-
tion. Refer to the “Erase/Program Operations” tables in
the “AC Characteristics” section for parameters, and to
Figure 14 for timing diagrams.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F400BB-70EE | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BB-70SE | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BB-70EEB | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29LL800T-200EBB | 1M X 8 FLASH 3V PROM, 200 ns, PDSO48 |
| AM29LV004B-90FE | 512K X 8 FLASH 3V PROM, 90 ns, PDSO40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F400BB-70ED | 制造商:Spansion 功能描述:FLASH BOTTOM BLOCK 4MB SMD 29F400 制造商:Spansion 功能描述:FLASH BOTTOM BLOCK 4MB, SMD, 29F400 |
| AM29F400BB-70ED/T | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K/256K x 8bit/16bit 70ns 48-Pin TSOP T/R |
| AM29F400BB-70EF | 功能描述:閃存 4M (512KX8/256Kx16) Parallel NOR Fl 5V RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AM29F400BB-70EF\\T | 制造商:Spansion 功能描述: |
| AM29F400BB-70EF\T | 功能描述:閃存 4M (512KX8/256Kx16) Parallel NOR Fl 5V RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。