- 您現在的位置：買賣IC網 > PDF目錄366440 > AM29F400BT-90EF (Advanced Micro Devices, Inc.) 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29F400BT-90EF |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 4兆位（512畝x 8-Bit/256畝x 16位），5.0伏的CMOS只引導扇區閃存 |
| 文件頁數： | 17/43頁 |
| 文件大小： | 548K |
| 代理商： | AM29F400BT-90EF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
November1,2006 21505E5
Am29F400B
15
D A T A S H E E T
μs, otherwise the last address and command might not
be accepted, and erasure may begin. It is recom-
mended that processor interrupts be disabled during
this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector Erase
command is written. If the time between additional
sector erase commands can be assumed to be less
than 50 μs, the system need not monitor DQ3.
Any
command other than Sector Erase or Erase
Suspend during the time-out period resets the
device to reading array data.
The system must
rewrite the command sequence and any additional
sector addresses and commands.
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising
edge of the final WE# pulse in the command sequence.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. Note that a
hardware reset
during the
sector erase operation immediately terminates the
operation. The Sector Erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure data integrity.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the
status of the erase operation by using DQ7, DQ6, DQ2,
or RY/BY#. (Refer to “The Erase Resume command is
valid only during the Erase Suspend mode.” for infor-
mation on these status bits.)
Figure 3 illustrates the algorithm for the erase opera-
tion. Refer to the “Erase/Program Operations” tables in
the “AC Characteristics” section for parameters, and to
Figure 14 for timing diagrams.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F400BT-90EF0 | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90EI | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90EI0 | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90EK | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90EK0 | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F400BT-90EI\T | 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel 5V 4M-Bit 512K x 8/256K x 16 90ns 48-Pin TSOP T/R |
| AM29F400BT-90SE\T | 制造商:Spansion 功能描述:4 MEGABIT (512 K X 8-BIT/256 K X 16-BIT) CMOS 5.0 VOLT-ONLY BOOT SECTOR FLASH MEMORY |
| AM29F400BT-90SF\\T | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K/256K x 8bit/16bit 90ns 44-Pin SO T/R |
| AM29F400BT-90SF\T | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K/256K x 8bit/16bit 90ns 44-Pin SO T/R |
| AM29F400BT-90SI | 制造商:Spansion 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。