- 您現在的位置：買賣IC網 > PDF目錄366464 > AM29LV040B-60RJE (Advanced Micro Devices, Inc.) 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory PDF資料下載
參數資料
| 型號： | AM29LV040B-60RJE |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory |
| 中文描述： | 4兆位（512畝× 8位），3.0伏的CMOS只，均勻部門32引腳閃存 |
| 文件頁數： | 13/37頁 |
| 文件大?。?/td> | 471K |
| 代理商： | AM29LV040B-60RJE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
October11,2006 21354E4
Am29LV040B
13
D A T A S H E E T
COMMAND DEFINITIONS
Writing specific address and data commands or
sequences into the command register initiates device
operations. Table 4 defines the valid register command
sequences.
Writing incorrect address and data values
or writing them in the improper sequence may place the
device in an unknown state. A reset command is then
required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or
CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the appropriate timing diagrams in the
“AC Characteristics” section.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array
data after completing an Embedded Program or
Embedded Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The
system can read array data using the standard read
timings, except that if it reads at an address within
erase-suspended sectors, the device outputs status
data. After completing a programming operation in the
Erase Suspend mode, the system may once again
read array data with the same exception. See “Erase
Suspend/Erase Resume Commands” for more infor-
mation on this mode.
The system
must
issue the reset command to re-
enable the device for reading array data if DQ5 goes
high, or while in the autoselect mode. See the “Reset
Command” section, next.
See also “Requirements for Reading Array Data” in the
“Device Bus Operations” section for more information.
The Read Operations table provides the read parame-
ters, and Figure 11 shows the timing diagram.
Reset Command
Writing the reset command to the device resets the
device to reading array data. Address bits are don’t
care for this command.
The reset command may be written between the
sequence cycles in an erase command sequence
before erasing begins. This resets the device to reading
array data. Once erasure begins, however, the device
ignores reset commands until the operation is
complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
reading array data (also applies to programming in
Erase Suspend mode). Once programming begins,
however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the
sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command
must
be written to return to reading array data (also applies
to autoselect during Erase Suspend).
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to
reading array data (also applies during Erase
Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and devices codes,
and determine whether or not a sector is protected.
Table 4 shows the address and data requirements. This
method is an alternative to that shown in Table 3, which
is intended for PROM programmers and requires V
ID
on address bit A9.
The autoselect command sequence is initiated by
writing two unlock cycles, followed by the autoselect
command. The device then enters the autoselect
mode, and the system may read at any address any
number of times, without initiating another command
sequence. A read cycle at address 00h retrieves the
manufacturer code. A read cycle at address 01h
returns the device code. A read cycle containing a
sector address (SA) and the address 02h returns 01h if
that sector is protected, or 00h if it is unprotected. Refer
to Table 2 for valid sector addresses.
The system must write the reset command to exit the
autoselect mode and return to reading array data.
Byte Program Command Sequence
The byte program command sequence programs one
byte into the device. Programming is a four-bus-cycle
operation. The program command sequence is initi-
ated by writing two unlock write cycles, followed by the
program set-up command. The program address and
data are written next, which in turn initiate the
Embedded Program algorithm. The system is
not
required to provide further controls or timings. The
device automatically provides internally generated
program pulses and verify the programmed cell margin.
Table 4 shows the address and data requirements for
the byte program command sequence.
Note that the
autoselect function is unavailable when a program
operation is in progress.
When the Embedded Program algorithm is complete,
the device then returns to reading array data and
addresses are no longer latched. The system can
determine the status of the program operation by using
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV040B-60RJF | 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory |
| AM29LV040B-60RJK | 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory |
| AM29LV040B-70ED | 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory |
| AM29LV040B-70EF | 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory |
| AM29LV040B-70EK | 4 Megabit (512 K x 8-Bit) CMOS 3.0 Volt-only, Uniform Sector 32-Pin Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| am29lv040b-60rji | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 4Mbit 512K x 8bit 60ns 32-Pin PLCC 制造商:Advanced Micro Devices 功能描述: |
| AM29LV040B-60RJI\\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 4MBIT 512KX8 60NS 32PLCC - Rail/Tube |
| AM29LV040B-60RJI\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 4MBIT 512KX8 60NS 32PLCC - Rail/Tube |
| AM29LV040B-70EC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 512K x 8, 32 Pin, Plastic, TSSOP |
| AM29LV040B-70ED | 制造商:Spansion 功能描述:FLASH 3V 4MB SMD 29LV040 TSOP32 |
發布緊急采購，3分鐘左右您將得到回復。