參數資料
型號: AM29LV065MU120WHF
廠商: Advanced Micro Devices, Inc.
英文描述: 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
中文描述: 64兆位(8米× 8位)的MirrorBit⑩3.0伏特,只有統一部門閃存記憶體與VersatileI /輸出⑩控制
文件頁數: 32/62頁
文件大小: 778K
代理商: AM29LV065MU120WHF
30
Am29LV065MU
September 12, 2006
D A T A S H E E T
Figure 5.
Program Operation
Program Suspend/Program Resume
Command Sequence
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. When the Program Sus-
pend command is written during a programming pro-
cess, the device halts the program operation within
15
μ
s maximum (5
μ
s typical) and updates the status
bits. Addresses are not required when writing the Pro-
gram Suspend command.
After the programming operation has been sus-
pended, the system can read array data from any
non-suspended sector. The Program Suspend com-
mand may also be issued during a programming oper-
ation while an erase is suspended. In this case, data
may be read from any addresses not in Erase Sus-
pend or Program Suspend. If a read is needed from
the SecSi Sector area (One-time Program area), then
user must use the proper command sequences to
enter and exit this region.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes
as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
“Autoselect Command Sequence” on page 26. for
more information.
After the Program Resume command is written, the
device reverts to programming. The system can deter-
mine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard pro-
gram operation. See “Write Operation Status” on
page 35. for more information.
The system must write the Program Resume com-
mand (address bits are don’t care) to exit the Program
Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ig-
nored. Another Program Suspend command can be
written after the device has resume programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
Note:
See Table 10 for program command sequence.
相關PDF資料
PDF描述
AM29LV065MU25EF 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV065MU25EI 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV065MU25FF 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV065MU25FI 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV065MU25WHF 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
相關代理商/技術參數
參數描述
AM29LV081B-120ED 制造商:Spansion 功能描述:IC SM FLASH 3V 8MB
AM29LV081B-120ED 制造商:Spansion 功能描述:FLASH MEMORY IC
AM29LV081B-70EC 制造商:Advanced Micro Devices 功能描述: 制造商:Atmel Corporation 功能描述:
AM29LV081B-70ED 制造商:Spansion 功能描述:IC FLASH MEMORY PARALLEL 制造商:Advanced Micro Devices 功能描述:NOR Flash, 1M x 8, 40 Pin, Plastic, TSSOP
AM29LV081B-70ED 制造商:Spansion 功能描述:Flash Memory IC