- 您現在的位置：買賣IC網 > PDF目錄366473 > AM29LV081B-90EF (Advanced Micro Devices, Inc.) 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29LV081B-90EF |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory |
| 中文描述： | 8兆位（1米× 8位）的CMOS 3.0伏特，只有統一部門閃存 |
| 文件頁數： | 10/40頁 |
| 文件大小： | 438K |
| 代理商： | AM29LV081B-90EF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
8
Am29LV081B
21525D6
October 12, 2006
DA T A S HE E T
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the Autoselect Mode and Autoselect
Command Sequence sections for more information.
I
CC2
in the DC Characteristics table represents the ac-
tive current specification for the write mode. The “AC
Characteristics” section contains timing specification
tables and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and I
CC
read specifications apply. Refer to “Write Operation
Status” for more information, and to “AC Characteris-
tics” for timing diagrams.
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at V
CC
± 0.3 V.
(Note that this is a more restricted voltage range than
V
IH
.) If CE# and RESET# are held at V
IH
, but not within
V
CC
± 0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device requires
standard access time (t
CE
) for read access when the
device is in either of these standby modes, before it is
ready to read data.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
When the RESET# input is held at V
SS
±
0.3 V, the de-
vice enters the standby mode within a period of t
RPD
,
tristates all data output pins, and ignores all read/write
attempts for the duration of the RESET# pulse. This
mode is “RESET# controlled,” since CE# is don’t care
under this condition. Once the RESET# pin is set
high, the device requires t
RH
of wake up time in addi-
tion to t
CE
access time for reading data. This method
also terminates any operation in progress and resets
the device.
I
CC3
in the DC Characteristics table represents the
standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device
energy consumption. The device automatically enables
this mode when addresses remain stable for t
ACC
+ 30
ns. The automatic sleep mode is independent of the
CE#, WE#, and OE# control signals. Standard address
access timings provide new data when addresses are
changed. While in sleep mode, output data is latched
and always available to the system. I
CC4
in the DC
Characteristics table represents the automatic sleep
mode current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the RE-
SET# pin is driven low for at least a period of t
RP
, the
device
immediately terminates
any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at V
SS
±0.3 V, the device
draws CMOS standby current (I
CC4
). If RESET# is held
at V
IL
but not within V
SS
±0.3 V, the standby current will
be greater.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
If RESET# is asserted during a program or erase op-
eration, the RY/BY# pin remains a “0” (busy) until the
internal reset operation is complete, which requires a
time of t
READY
(during Embedded Algorithms). The
system can thus monitor RY/BY# to determine
whether the reset operation is complete. If RESET# is
asserted when a program or erase operation is not ex-
ecuting (RY/BY# pin is “1”), the reset operation is
completed within a time of t
READY
(not during Embed-
ded Algorithms). The system can read data t
RH
after
the RESET# pin returns to V
IH
.
Refer to the AC Characteristics tables for RESET# pa-
rameters and to Figure 14 for the timing diagram.
Output Disable Mode
When the OE# input is at V
IH
, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV081B-90EK | 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory |
| AM29LV102BB-90EI | 2 Megabit (256 K x 8-Bit) CMOS 3.0 Volt-only, Boot Sector 32-Pin Flash Memory |
| AM29LV102BB-55RJC | 2 Megabit (256 K x 8-Bit) CMOS 3.0 Volt-only, Boot Sector 32-Pin Flash Memory |
| Am29LV102BB-55RJCB | 2 Megabit (256 K x 8-Bit) CMOS 3.0 Volt-only, Boot Sector 32-Pin Flash Memory |
| Am29LV102BB-55RJE | 2 Megabit (256 K x 8-Bit) CMOS 3.0 Volt-only, Boot Sector 32-Pin Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV116BT-90EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV116DB-70EI | 制造商:Spansion 功能描述: |
| AM29LV116DB-90EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV116DT-70EC | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8 70ns 40-Pin TSOP |
| AM29LV116DT-90EI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。