- 您現在的位置：買賣IC網 > PDF目錄362262 > AM29LV160BT-90FE x8/x16 Flash EEPROM PDF資料下載
參數資料
| 型號： | AM29LV160BT-90FE |
| 英文描述： | x8/x16 Flash EEPROM |
| 中文描述： | x8/x16閃存EEPROM |
| 文件頁數： | 18/35頁 |
| 文件大?。?/td> | 744K |
| 代理商： | AM29LV160BT-90FE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
18
Am29LV040B
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously pro-
grammed to “0.”
Only an erase operation can change
a “0” back to a “1.”
Under this condition, the device
halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue the
reset command to return the device to reading array
data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase com-
mand. When the time-out is complete, DQ3 switches
from “0” to “1.” If the time between additional sector
erase commands from the system can be assumed to
be less than 50 μs, the system need not monitor DQ3.
See also the “Sector Erase Command Sequence”
section.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data#
Polling) or DQ6 (Toggle Bit I) to ensure the device has
accepted the command sequence, and then read DQ3.
If DQ3 is “1”, the internally controlled erase cycle has
begun; all further commands (other than Erase Sus-
pend) are ignored until the erase operation is complete.
If DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been
accepted. Table 5 shows the outputs for DQ3.
START
No
Yes
Yes
DQ5 = 1
No
Yes
Toggle Bit
= Toggle
No
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Read DQ7–DQ0
Toggle Bit
= Toggle
Read DQ7–DQ0
Twice
Read DQ7–DQ0
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1” . See text.
Figure 4.
Toggle Bit Algorithm
(Notes
1, 2)
(Note 1)
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV160BT-90FI | x8/x16 Flash EEPROM |
| AM29LV160BT-90SC | x8/x16 Flash EEPROM |
| AM29LV160BT-90SE | x8/x16 Flash EEPROM |
| AM29LV160BT-90SI | x8/x16 Flash EEPROM |
| AM29LV200BB120WAE | EEPROM|FLASH|128KX16/256KX8|CMOS|BGA|48PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV160DB120EI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV160DB-120EIT | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 120NS 48TSOP - Tape and Reel |
| AM29LV160DB120WCCT | 制造商:Advanced Micro Devices 功能描述: |
| am29lv160db120wcis | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV160DB70EC | 制造商:FLASH29LV160 功能描述:AM29LV160DB-70EC |
發布緊急采購，3分鐘左右您將得到回復。