- 您現在的位置：買賣IC網 > PDF目錄366488 > AM29LV160MT50WAI (Advanced Micro Devices, Inc.) 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29LV160MT50WAI |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 16兆位（2米× 8位/ 1個M x 16位）的MirrorBit?3.0伏，只引導扇區閃存 |
| 文件頁數： | 26/63頁 |
| 文件大?。?/td> | 967K |
| 代理商： | AM29LV160MT50WAI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
24
Am29LV160M
25974B5 January31,2007
D a t a S h e e t
programming begins, however, the device ignores reset commands until the op-
eration is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command
must
be
written to return to reading array data (also applies to autoselect during Erase
Suspend).
If DQ5 goes high during a program or erase operation, writing the reset command
returns the device to reading array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and devices codes, and determine whether or not a sector is protected.
Table 10, on page 31
and
Table 11, on page 32
show the address and data re-
quirements. This method is an alternative to that shown in
Table 4, on page 15
,
which is intended for PROM programmers and requires V
ID
on address bit A9.
The autoselect command sequence is initiated by writing two unlock cycles, fol-
lowed by the autoselect command. The device then enters the autoselect mode,
and the system may read at any address any number of times, without initiating
another command sequence.
A read cycle at address XX00h retrieves the manufacturer code. A read cycle at
address XX01h returns the device code. A read cycle containing a sector address
(SA) and the address XX02h in word mode (or XX04h in byte mode) returns
XX01h if that sector is protected, or 00h if it is unprotected. Refer to
Table 2, on
page 13
and
Table 3, on page 14
for valid sector addresses.
The system must write the reset command to exit the autoselect mode and return
to reading array data.
Word/Byte Program Command Sequence
The system may program the device by word or byte, depending on the state
of the BYTE# pin. Programming is a four-bus-cycle operation. The program
command sequence is initiated by writing two unlock write cycles, followed by
the program set-up command. The program address and data are written next,
which in turn initiate the Embedded Program algorithm. The system is
not
re-
quired to provide further controls or timings. The device automatically
generates the program pulses and verifies the programmed cell margin.
Table 10, on page 31
and
Table 11, on page 32
show the address and data re-
quirements for the byte program command sequence.
Note that the Secured
Silicon Sector, autoselect, and CFI functions are unavailable when a program
operation is in progress.
When the Embedded Program algorithm is complete, the device then returns to
reading array data and addresses are no longer latched. The system can deter-
mine the status of the program operation by using DQ7, DQ6, or RY/BY#. See
“Write Operation Status” on page 33
for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm
are ignored. Note that a
hardw are reset
immediately terminates the program-
ming operation. The Byte Program command sequence should be reinitiated once
the device resets to reading array data, to ensure data integrity.
Programming is allowed in any sequence and across sector boundaries.
A bit
cannot be programmed from a “ 0” back to a “ 1” .
Attempting to do so may
halt the operation and set DQ5 to “1,” or cause the Data# Polling algorithm to
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV160MT70REI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT70RFI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT70RPCI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT70RWAI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT85EI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit TM 3.0 Volt-only Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV160MT70EI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 70NS 48TSOP - Trays |
| AM29LV200BB-120EC | 制造商:Advanced Micro Devices 功能描述:128K X 16 FLASH 3V PROM, 120 ns, PDSO48 |
| AM29LV200BB-90EC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 128K x 16, 48 Pin, Plastic, TSSOP |
| AM29LV200BB-90FC | 制造商:Advanced Micro Devices 功能描述:2 Mb (128K x 16) Boot Sector, Flash Memory |
| AM29LV256MH120RPGI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 256MBIT 32MX8/16MX16 120NS 64BGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。