參數資料
型號： AM29LV400BB-120DWC1
元件分類： EEPROM
英文描述： EEPROM
中文描述： EEPROM的
文件頁數： 16/35頁
文件大?。?/td> 744K
代理商： AM29LV400BB-120DWC1
16
Am29LV040B
WRITE OPERATION STATUS
The device provides several bits to determine the
status of a write operation: DQ2, DQ3, DQ5, DQ6, and
DQ7. Table 5 and the following subsections describe
the functions of these bits. DQ7 and DQ6 each offer a
method for determining whether a program or erase
operation is complete or in progress. These three bits
are discussed first.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host
system whether an Embedded Algorithm is in progress
or completed, or whether the device is in Erase Sus-
pend. Data# Polling is valid after the rising edge of the
final WE# pulse in the program or erase command
sequence.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum pro-
grammed to DQ7. This DQ7 status also applies to
programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device
outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for
approximately 1
μs, then the device returns to reading
array data.
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
This is analogous to the complement/true datum output
described for the Embedded Program algorithm: the
erase function changes all the bits in a sector to “1”;
prior to this, the device outputs the “complement,” or
“0.” The system must provide an address within any of
the sectors selected for erasure to read valid status
information on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data#
Polling on DQ7 is active for approximately 100 μs, then
the device returns to reading array data. If not all
selected sectors are protected, the Embedded Erase
algorithm erases the unprotected sectors, and ignores
the selected sectors that are protected.
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7–
DQ0 on the
following
read cycles. This is because DQ7
may change asynchronously with DQ0–DQ6 while
Output Enable (OE#) is asserted low. Figure 14, Data#
Polling Timings (During Embedded Algorithms), in the
“AC Characteristics” section illustrates this.
Table 5 shows the outputs for Data# Polling on DQ7.
Figure 3 shows the Data# Polling algorithm.
DQ7 = Data
Yes
No
No
DQ5 = 1
No
Yes
Yes
FAIL
PASS
Read DQ7–DQ0
Addr = VA
Read DQ7–DQ0
Addr = VA
DQ7 = Data
START
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within any
sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
2.
DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
Figure 3.
Data# Polling Algorithm
相關PDF資料
PDF描述
AM29LV400BB-120DWE1 EEPROM
AM29LV400BB-120DWI1 EEPROM
AM29LV400BB-120EC x8/x16 Flash EEPROM
AM29LV400BB-120EE x8/x16 Flash EEPROM
AM29LV400BB-120EI x8/x16 Flash EEPROM
相關代理商/技術參數
參數描述
AM29LV400BB-120EC 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 4M-Bit 512K x 8/256K x 16 120ns 48-Pin TSOP
AM29LV400BB-120EI 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 4Mbit 512K/256K x 8bit/16bit 120ns 48-Pin TSOP
AM29LV400BB-120SC 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 4Mbit 512K/256K x 8bit/16bit 120ns 44-Pin SOP
AM29LV400BB-120WAI 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 4M-Bit 512K x 8/256K x 16 120ns 48-Pin FBGA
AM29LV400BB-55RWAI 制造商:Spansion 功能描述:SPZAM29LV400BB-55RWAI 4M FLASH EOL150606
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*