- 您現在的位置：買賣IC網 > PDF目錄223348 > Am29LV400T-90RWACB (Advanced Micro Devices, Inc.) 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | Am29LV400T-90RWACB |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 4兆位（512畝x 8-Bit/256畝x 16位），3.0伏的CMOS只引導扇區閃存 |
| 文件頁數： | 13/40頁 |
| 文件大?。?/td> | 516K |
| 代理商： | AM29LV400T-90RWACB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Am29LV400
20
PREL I M I N AR Y
The remaining scenario is that the system initially de-
termines that the toggle bit is toggling and DQ5 has not
gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, de-
termining the status as described in the previous para-
graph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the
beginning of the algorithm when it returns to determine
the status of the operation (top of Figure 5).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously
programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue
the reset command to return the device to reading
array data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase com-
mand. When the time-out is complete, DQ3 switches
from “0” to “1.” If the time between additional sector
erase commands from the system can be assumed to
be less than 50
s, the system need not monitor DQ3.
See also the “Sector Erase Command Sequence” sec-
tion.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If
DQ3 is “1”, the internally controlled erase cycle has be-
gun; all further commands (other than Erase Suspend)
are ignored until the erase operation is complete. If
DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been ac-
cepted. Table 6 shows the outputs for DQ3.
START
No
Yes
DQ5 = 1?
No
Yes
Toggle Bit
= Toggle?
No
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Read DQ7–DQ0
Toggle Bit
= Toggle?
Read DQ7–DQ0
Twice
Read DQ7–DQ0
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1” . See text.
20514C-9
Figure 5.
Toggle Bit Algorithm
(Notes
相關PDF資料 |
PDF描述 |
|---|---|
| Am29LV400T-90RWAE | FEEDTHRU CAPACITOR, 470PF 4A 100VFEEDTHRU CAPACITOR, 470PF 4A 100V; Capacitance:0.47nF; Voltage rating, DC:100V; Capacitor dielectric type:Ceramic Multi-Layer; Tolerance, +:50%; Tolerance, -:20%; Temp, op. max:125(degree C); Temp, |
| Am29LV400T-90RWAEB | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV400T-90RWAC | Ceramic Multilayer Capacitor; Capacitance:100pF; Capacitance Tolerance:+50, -20 %; Working Voltage, DC:100V; Dielectric Characteristic:NP0; Package/Case:1206; Series:W3F; Leaded Process Compatible:Yes |
| AM29LV400B-90RWAC | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV640DH90RZE | 8 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV640DH90REI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 90NS 48TSOP - Trays |
| AM29LV640DL90RZI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640DU-90NI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640DU90REI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 90NS 48TSOP - Trays |
| AM29LV640DU-90RWHIT | 制造商:Advanced Micro Devices 功能描述:63-BALL FINE-PITCH BALL GRID ARRAY (FBGA) 0.80 MM PITCH, 11 X 12 MM PACKAGE (FBE063) |
發布緊急采購，3分鐘左右您將得到回復。