參數資料
型號: AM29LV640MH101RPCI
廠商: ADVANCED MICRO DEVICES INC
元件分類: PROM
英文描述: 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
中文描述: 4M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝: 13 X 11 MM, 1 MM PITCH, BGA-64
文件頁數: 31/62頁
文件大?。?/td> 602K
代理商: AM29LV640MH101RPCI
December 14, 2005
Am29LV640MH/L
29
D A T A S H E E T
Note:
See
Table 11
for program command sequence.
Figure 5.
Program Operation
Program Suspend/Program Resume
Command Sequence
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. When the Program Sus-
pend command is written during a programming pro-
cess, the device halts the program operation within 15
μ
s maximum (5
μ
s typical) and updates the status bits.
Addresses are not required when writing the Program
Suspend command.
After the programming operation has been sus-
pended, the system can read array data from any
non-suspended sector. The Program Suspend com-
mand may also be issued during a programming oper-
ation while an erase is suspended. In this case, data
may be read from any addresses not in Erase Sus-
pend or Program Suspend. If a read is needed from
the SecSi Sector area (One-time Program area), then
user must use the proper command sequences to
enter and exit this region.
Note that the SecSi Sector,
autoselect, and CFI functions are unavailable when an
program operation is in progress.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect
codes as required. When the device exits the autose-
lect mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
Autoselect Command Sequence for more information.
After the Program Resume command is written, the
device reverts to programming. The system can de-
termine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard pro-
gram operation. See
Write Operation Status
for more
information.
The system must write the Program Resume com-
mand (address bits are don’t care) to exit the Program
Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ig-
nored. Another Program Suspend command can be
written after the device has resume programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料
PDF描述
AM29LV640MH112EI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV640MH112FI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV640MH112PCI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV640MH112REI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
AM29LV640MH112RFI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
相關代理商/技術參數
參數描述
AM29LV640MH112REI 制造商:Advanced Micro Devices 功能描述:4M X 16 FLASH 3V PROM, 110 ns, PDSO56
AM29LV640MU101RPCI 制造商:Advanced Micro Devices 功能描述:
AM29LV640MU90NI 制造商:Advanced Micro Devices 功能描述:
AM29LV640MU90RPC1 制造商:Advanced Micro Devices 功能描述:
AM29LV640MU90RPCI 制造商:Advanced Micro Devices 功能描述: