參數資料
型號: AM29LV640MT100PCI
廠商: ADVANCED MICRO DEVICES INC
元件分類: PROM
英文描述: 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Boot Sector Flash Memory
中文描述: 4M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝: 13 X 11 MM, 1 MM PITCH, FORTIFIED, BGA-64
文件頁數: 41/66頁
文件大小: 836K
代理商: AM29LV640MT100PCI
February1,2007 26190C8
Am29LV640MT/B
39
D A T A S H E E T
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin
which indicates whether an Embedded Algorithm is in
progress or complete. The RY/BY# status is valid after
the rising edge of the final WE# pulse in the command
sequence. Since RY/BY# is an open-drain output, sev-
eral RY/BY# pins can be tied together in parallel with a
pull-up resistor to V
CC
.
If the output is low (Busy), the device is actively eras-
ing or programming. (This includes programming in
the Erase Suspend mode.) If the output is high
(Ready), the device is in the read mode, the standby
mode, or in the erase-suspend-read mode.
Table 14
shows the outputs for RY/BY#.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or com-
plete, or whether the device has entered the Erase
Suspend mode. Toggle Bit I can be read at any ad-
dress, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
program or erase operation), and during the sector
erase time-out.
During an Embedded Program or Erase algorithm op-
eration, successive read cycles to any address cause
DQ6 to toggle. The system can use either OE# or CE#
to control the read cycles. When the operation is com-
plete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors
selected for erasing are protected, DQ6 toggles for approxi-
mately 100 μs, then returns to reading array data. If not all
selected sectors are protected, the Embedded Erase algo-
rithm erases the unprotected sectors, and ignores the se-
lected sectors that are protected.
The system can use DQ6 and DQ2 together to determine
whether a sector is actively erasing or is erase-suspended.
When the device is actively erasing (that is, the Embedded
Erase algorithm is in progress), DQ6 toggles. When the de-
vice enters the Erase Suspend mode, DQ6 stops toggling.
However, the system must also use DQ2 to determine
which sectors are erasing or erase-suspended. Alterna-
tively, the system can use DQ7. See
DQ7: Data# Polling on
page38
).
If a program address falls within a protected sector,
DQ6 toggles for approximately 1
μ
s after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Pro-
gram algorithm is complete.
Table 14
shows the outputs for Toggle Bit I on DQ6.
Figure 9
shows the toggle bit algorithm.
Figure 21
in
AC Characteristics
shows the toggle bit timing dia-
grams.
Figure 22
shows the differences between DQ2
and DQ6 in graphical form. See also
DQ2: Toggle Bit II
on page 40
.
相關PDF資料
PDF描述
AM29LV640MT100REF 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Boot Sector Flash Memory
AM29LV640MT100REI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Boot Sector Flash Memory
AM29LV640MT120PCI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Boot Sector Flash Memory
AM29LV640MT120REF 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Boot Sector Flash Memory
AM29LV640MT120REI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Boot Sector Flash Memory
相關代理商/技術參數
參數描述
AM29LV640MU101RPCI 制造商:Advanced Micro Devices 功能描述:
AM29LV640MU90NI 制造商:Advanced Micro Devices 功能描述:
AM29LV640MU90RPC1 制造商:Advanced Micro Devices 功能描述:
AM29LV640MU90RPCI 制造商:Advanced Micro Devices 功能描述:
AM29LV641DH120REF 制造商:Spansion 功能描述:Flash Memory IC