參數資料
型號: Am29SL800BB170FCB
廠商: Advanced Micro Devices, Inc.
英文描述: 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
中文描述: 8兆位(1 M中的x 8-Bit/512畝x 16位),1.8伏的CMOS只超低電壓快閃記憶體
文件頁數: 18/41頁
文件大?。?/td> 543K
代理商: AM29SL800BB170FCB
18
Am29SL800B
A D V A N C E I N F O R M A T I O N
Table 5.
Am29SL800B Command Definitions
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed.
Addresses latch on the falling edge of the WE# or CE# pulse,
whichever happens later.
PD = Data to be programmed at location PA. Data latches on the
rising edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A18–A12 uniquely select any sector.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles
are write operations.
4. Data bits DQ15–DQ8 are don’t cares for unlock and
command cycles.
5. Address bits A18–A11 are don’t cares for unlock and
command cycles, unless SA or PA required.
6. No unlock or command cycles required when reading array
data, unless SA or PA required.
7. The Reset command is required to return to reading array
data when device is in the autoselect mode, or if DQ5 goes
high (while the device is providing status data).
8. The fourth cycle of the autoselect command sequence is a
read cycle.
9. The data is 00h for an unprotected sector and 01h for a
protected sector. See “Autoselect Command Sequence” for
more information.
10. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
11. The Unlock Bypass Reset command is required to return to
reading array data when the device is in the unlock bypass
mode.
12. The system may read and program n non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend
mode. The Erase Suspend command is valid only during a
sector erase operation.
13. The Erase Resume command is valid only during the Erase
Suspend mode.
Command
Sequence
(Note 1)
Bus Cycles (Notes 2-5)
Third
Addr
Data Addr
First
Second
Addr
Fourth
Fifth
Sixth
Addr
RA
XXX
555
AAA
555
AAA
555
AAA
Data
RD
F0
Data
Data
Addr Data
Addr
Data
Read (Note 6)
Reset (Note 7)
1
1
Manufacturer ID
Word
Byte
Word
Byte
Word
Byte
4
AA
2AA
555
2AA
555
2AA
555
55
555
AAA
555
AAA
555
AAA
90
X00
01
Device ID,
Top Boot Block
4
AA
55
90
X01
22EA
EA
226B
6B
XX00
XX01
00
01
X02
X01
Device ID,
Bottom Boot Block
4
AA
55
90
X02
Sector Protect Verify
(Note 9)
Word
4
555
AA
2AA
55
555
90
(SA)
X02
Byte
AAA
555
AAA
(SA)
X04
Program
Word
Byte
Word
Byte
4
555
AAA
555
AAA
XXX
XXX
555
AAA
555
AAA
XXX
XXX
AA
2AA
555
2AA
555
PA
XXX
2AA
555
2AA
555
55
555
AAA
555
AAA
A0
PA
PD
Unlock Bypass
3
AA
55
20
Unlock Bypass Program (Note 10)
Unlock Bypass Reset (Note 11)
2
2
A0
90
PD
00
Chip Erase
Word
Byte
Word
Byte
6
AA
55
555
AAA
555
AAA
80
555
AAA
555
AAA
AA
2AA
555
2AA
555
55
555
AAA
10
Sector Erase
6
AA
55
80
AA
55
SA
30
Erase Suspend (Note 12)
Erase Resume (Note 13)
1
1
B0
30
C
A
相關PDF資料
PDF描述
AM29SL800BT170FI 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
AM29SL800BT170WBC 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
AM29SL800BB170WBC 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
AM29SL800BT170WBI 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
AM29SL800BB170WBI 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
相關代理商/技術參數
參數描述
AM29SL800DB120WCI 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 8MBIT 1MX8/512KX16 120NS 48FBGA - Trays
AM29SL800DB90WAD 制造商:Spansion 功能描述:
AM29X305ADC 制造商:Advanced Micro Devices 功能描述:Microprocessor, 8 Bit, 50 Pin, Ceramic, DIP
AM2A016 制造商:MAG-LITE 功能描述:Bulk
AM2A026 制造商:MAG-LITE 功能描述:Bulk