參數資料
型號: AMC7820
英文描述: Analog Monitoring and Control Circuitry
中文描述: 模擬監測和控制電路
文件頁數: 17/28頁
文件大?。?/td> 468K
代理商: AMC7820
AMC7820
SBAS231B
www.ti.com
17
SWITCHES
The AMC7820 has four internal switches (SW1, SW2, SW3,
and SW4) to shut down the TEC and laser diode (see the
application in Figure 7 for more detail).
SW1 and SW2 are controlled by the internal signals
SW1_DISABLE and SW2_DISABLE, respectively. The sta-
tus of these signals is determined by the four LSBs of the
SHUTDOWN register (bits 0 through 3) designated
SW1-1/SW1-0 and SW2-1/SW2-0. After power-on or reset,
SW1 connects to ground, and SW2 connects to SW3.
SW3 is controlled by bits 2 and 3 (POL1/POL0) of the
CONFIGURATION/STATUS register. After power-on or re-
set, SW3 connects to 2.5V (the internal reference voltage on
pin 26).
Closing switch SW4 activates the TEC soft-start function
implemented by the TEC SOFT_START CONTROLLER.
SW4 is controlled by the internal signals SW2_DISABLE and
SOFT_START_CTR. The LSBs (TS1/TS0) of the CONFIGU-
RATION/STATUS register determines the status of
SOFT_START_CTR. After power-on or reset, SW4 is closed
and soft-start is activated. The host can write
00
to TS1/TS0
to turn off SW4.
The host can change the status of any switch by writing a
proper pattern into the appropriate registers (refer to the
AMC7820 Registers section).
TEC SOFT_START_CONTROLLER
This controller provides a soft start for a bidirectional TEC
Driver when OPA7 is configured as an integrator (see Figure
6) and the TEC driver is referenced to 2.5V (see the Applica-
tion section). Pin 1 (SW2_OUT) drives the external TEC driver.
A value of 2.5V from this pin sets the TEC driver output current
to zero, implementing a safe (zero current) starting condition.
After power-on or reset, switch SW2 is disabled interrupting
control of the external TEC driver by the integrator OPA7. The
actions of switches SW2 and SW3 apply 2.5V to pin 1, setting
the external TEC driver output current to zero. Switch SW4 is
also closed and the TEC SOFT_START_CONTROLLER is
enabled. This controller drives the output of OPA7 to 2.5V
which corresponds to zero TEC current. When the loop control
of the external TEC driver is resumed, the TEC current is
safely ramped up from zero. If the soft start controller is
disabled and the control loop is also diabled with SW2, OPA7
will continue to integrate until its output reaches a supply rail.
This will result in max current drive to the TEC, when the loop
is enabled (a hard start).
Since the THERM_I_OUTPUT and DAC0 reference are
derived from the same reference, they track indepen-
dently of any reference voltage drift, as shown in Figure 4.
This can be viewed as a bridge arrangement common in
instrumentation. When the temperature measured by the
thermistor is equal to the temperature represented by the
DAC
s output voltage, the voltages at pin 2 and pin 6 are
equal regardless of the reference drift caused by the
change of the ambient temperature or other conditions.
Figure 5 shows the typical performance of pin 2 minus pin
6 voltage tracking over
40
°
C to +85
°
C. The error is
+0.75mV at
40
°
C and
0.4mV at +85
°
C, which, out of a
50mV/
°
C sensitivity for the thermistor, is equivalent to
0.015
°
C and 0.008
°
C, respectively.
FIGURE 4. The Thermistor Feedback and Setpoint Viewed
as a Bridge.
Thermistor
10k
at 25
°
C
1.0V
R
R
THERM_I_OUTPUT
100
μ
A
DAC0
2
26
1.0V
6
44
DAC Set to 1.0V
7
FIGURE 5. Change in (Vpin2
Vpin6) vs Temperature.
CHANGE IN (Vpin2
Vpin6) vs TEMPERATURE
(For Internal or External Reference)
Temperature (
°
C)
D
°
C
2.0
1.5
1.0
0.5
0.0
0.5
1.0
1.5
2.0
50
25
0
25
50
75
100
相關PDF資料
PDF描述
AMC78L05 100mA / 3-TERMINAL 5V REGULATOR
AMC78L05DM 100mA / 3-TERMINAL 5V REGULATOR
AMC78L05DMF 100mA / 3-TERMINAL 5V REGULATOR
AMC78L05LP 100mA / 3-TERMINAL 5V REGULATOR
AMC78L05LPF 100mA / 3-TERMINAL 5V REGULATOR
相關代理商/技術參數
參數描述
AMC7820EVM 功能描述:數據轉換 IC 開發工具 AMC7820 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
AMC7820Y 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG MONITORING AND CONTROL
AMC7820Y/250 功能描述:數據轉換系統 Analog Monitoring & Control Circuitry RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
AMC7820Y/250G4 功能描述:數據轉換系統 Analog Monitoring & Control Circuitry RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
AMC7820Y/2K 功能描述:數據轉換系統 Analog Monitoring & Control Circuitry RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel