參數資料
型號： AMC8500DE16
廠商： Electronic Theatre Controls, Inc.
英文描述： TWO PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
中文描述： 兩相流變速風扇電機控制器
文件頁數： 12/27頁
文件大小： 648K
代理商： AMC8500DE16
Preliminary Specification
aMC8500
Motor Drives
The aMC8500 contains two 0.5
N-channel power MOSFETs that are designed to directly drive the motor coils from the
Phase 1 and Phase 2 outputs. The drive characteristics are shown in Figures 9 and 10. Each output contains a 36 V zener
with a series diode that connects from the drain to the gate. This configuration provides active clamp protection for the
MOSFETs when switching off the inductive motor load. In applications that demand driving higher current or higher voltage
motors, external MOSFET power transistors can be used. Two examples are shown in Figures 29 and 30. Although this
device is designed to drive two phase half wave motors, a method for driving single phase full wave motors is shown in
Figure 31.
Due to the inherent winding coupling that is present in two phase motors, the drain voltage of the off phase will be driven
negative and current will be sourced from that output. This current will cause additional device heating and may affect
operation of high current motors at elevated ambient temperatures. A simple solution is to place the cathode of a low forward
drop Schottky diode from each drive output to ground. Likewise if the motor windings are highly inductive, the internal active
clamp will be required to dissipate this energy which will also result in additional heating. This too can be eliminated with the
addition of an external zener diode connected from each drain to ground. The zener breakdown voltage should be in the
range of 30 V to 34 V.
Under Voltage Lockout and Auto Power Down
An Under Voltage Lockout circuit has been incorporated to prevent erratic device operation under low power supply
conditions. This circuit enables the Motor Drives when V
DD
rises above 4.7 V to guarantee full IC functionality, and disables
the drives when V
DD
falls below 4.2 V. The UVLO circuit has 500 mV of hysteresis to prevent oscillations as the thresholds
are crossed during power-up and power-down. The IC is designed to directly drive 9.0 V and 12 V motors.
As previously discussed, the device features a selectable auto Power Down mode. This mode is automatically entered
when the voltage applied to the Speed Control Input commands zero or less than zero percent on-time. When entered, the
power supply current is reduced from 1.6 mA to 130
μ
A. Refer to Figures 1, 2, and 14.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to protect the device in the event that the maximum junction temperature is
exceeded. When activated, typically at 140°C, the Motor Drive outputs are disabled to reduce device power dissipation. This
feature is intended to prevent catastrophic device failures in the event of accidental overheating. Although it is possible to
operate the device above the specified maximum junction temperature of 125°C, this protection feature is not intended to be
used as a substitute for proper thermal system design. When the junction temperature falls below 120°C, normal device
operation resumes. Refer to Figure 19.
P
P
SYSTEM APPLICATIONS
The following section shows numerous device circuit configurations and several complete fan control solutions with a brief
description. For clarity, many of the circuits show only the internal functional blocks that are of interest with the associated
pin numbers.
- 12 -
Andigilog, Inc. 2006
www.andigilog.com
August 2006 - 70A04018
Figure 19- Thermal Shutdown Operation
80
Thermal
Shut Down
Deactivated
Motor
Drives
Enabled
Thermal
Shut Down
Activated
Motor
Drives
Disabled
T
J(max)
T
J
, Junction Temperature (°C)
100
120
160
140
相關PDF資料
PDF描述
AMC8500QS16 TWO PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
AMC85020QS24 SINGLE PHASE VARIABLE SPEED ADVANCED FAN CONTROLLER
AMC8520 SINGLE PHASE VARIABLE SPEED ADVANCED FAN CONTROLLER
AMC8510 SINGLE PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
AMC8510D16 SINGLE PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
相關代理商/技術參數
參數描述
AMC8500QS16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TWO PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
AMC-8501-1OC12 制造商:Emerson Network Power 功能描述:OC12 ADVANCEDMC IO MODULE - Bulk
AMC85020QS24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE PHASE VARIABLE SPEED ADVANCED FAN CONTROLLER
AMC8510 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
AMC8510D16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE PHASE VARIABLE SPEED FAN MOTOR CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*