- 您現在的位置：買賣IC網 > PDF目錄362313 > AMMC-3040 18-36 GHz Double-Balanced Mixer with Integrated LO Amplifier/Multiplier PDF資料下載
參數資料
| 型號： | AMMC-3040 |
| 英文描述： | 18-36 GHz Double-Balanced Mixer with Integrated LO Amplifier/Multiplier |
| 中文描述： | 18-36 GHz的雙平衡與集成LO放大器，混頻器/乘法器 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 310K |
| 代理商： | AMMC-3040 |
5
Biasing for Fundamental Mixing
The recommended DC bias
condition for the AMMC-3040
LO amplifier when used as a
fundamental frequency mixer is
with all four drains connected
to a single 3.5 to 4.5V supply
and all four gates connected to
an adjustable negative supply
voltage as shown in Figure 16
(a). The gate voltage is adjusted
for a total drain supply current
of typically 150 to 250 mA.
The second, third, and fourth
stage DC drain bias lines are
connected internally and
therefore require only a single
bond wire. A separate bond
wire is needed for the first
stage DC drain bias, V
d1.
The third and fourth stage DC
gate bias lines are connected
internally. A total of three DC
gate bond wires are required:
one for V
g1
, one for V
g2
, and
one for the V
g3
/ V
g4
connection.
The internal matching circuitry
at the RF input creates a 50-
ohm DC and RF path to ground.
Any DC voltage applied to the
RF input must be maintained
below 1 volt, otherwise, a
blocking capacitor should be
used. The RF output is AC
coupled.
(a) Fundamental LO. Single drain and single gate supply assembly for using
the LO amplifier in fundamental frequency mixer applications.
(b) Sub-harmonic LO. Separate first-stage gate bias supply to use the LO
amplifier as a multiplier for application as a sub-harmonic mixer.
(Note: To assure stable operation bias supply feeds should be bypassed to ground with a capacitor, Cb > 100 pF typical)
Figure 16. AMMC-3040 Assembly diagram.
Gold Plated Shim
(optional)
To V
GG
DC Gate
Supply Feed
To V
DD
DC Drain
Supply Feed
100 pF
100 pF
IF
0.6 pF
~500 μm long
wire
LO
RF
Cb
Cb
Gold Plated Shim
(optional)
To V
GG
DC Gate
Supply Feed
To V
GG
DC Gate
Supply Feed
To V
DC Drain
Supply Feed
100 pF
100 pF
100 pF
IF
0.6 pF
~500 μm long
wire
LO
RF
Cb
Cb
Cb
No ground bond wires are
needed since the ground
connection is made by means of
plated through via holes to the
backside of the chip.
Biasing for Sub-Harmonic Mixing
The LO amplifier in the AMMC-
3040 can also be used as a
frequency doubler. Optimum
conversion efficiency as a
doubler is obtained with an
input power level of 3 to 8
dBm.
Frequency multiplication is
achieved by reducing the bias
on the first stage FET to
efficiently generate harmonics.
The remaining three stages are
then used to provide
amplification.
While many bias methods could
be used to generate and amplify
the desired harmonics within
the AMMC-3040’s LO amplifier,
the following information is
suggested as a starting point for
sub-harmonic mixing
applications.
Frequency doubling is
accomplished by biasing the
first stage FET at pinch-off by
setting V
g1
= V
p
≈
–1.1 volts.
The remaining three stages are
biased for normal amplification,
e.g., V
gg
is adjusted such that
I
d2
+ I
d3
+ I
d4
≈
250 mA. The
drain voltage, Vdd, for all four
stages should be 3.5 to 4.5 volts.
The assembly diagram shown in
Figure 16 (b) can be used as a
guideline.
In all cases, Cb > 100 pF to
assure stability.
IF Output Port
The IF output port is located
near the middle of the die,
allowing this connection to be
made from either side of the
chip for maximum layout
flexibility.
The LO and RF signals are
reflectively terminating at the IF
port by connecting a 20-mil
(500 um) long bond wire from
the IF output pad on the MMIC
to a shunt 0.6 pF chip capacitor
mounted off-chip as indicated
in Figure 16.
相關PDF資料 |
PDF描述 |
|---|---|
| AMMC-3040-W10 | 18-36 GHz Double-Balanced Mixer with Integrated LO Amplifier/Multiplier |
| AMMC-3040-W50 | 18-36 GHz Double-Balanced Mixer with Integrated LO Amplifier/Multiplier |
| AMMC-5023 | 23 GHz Low Noise Amplifier (21.2?26.5 GHz) |
| AMMC-6231 | 16?2 GHz Low Noise Amplifier |
| AMMC-6241 | 26-43 GHz Low Noise Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMMC-3040-W10 | 功能描述:上下轉換器 IC Mixer LO Amp RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| AMMC-3040-W50 | 功能描述:上下轉換器 IC Mixer LO Amp RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| AMMC-3041-W10 | 功能描述:上下轉換器 Mixer GaAs MMIC RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| AMMC-3041-W50 | 功能描述:上下轉換器 Mixer GaAs MMIC RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| AMMC-5023 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:23 GHz Low Noise Amplifier (21.2-26.5 GHz) |
發布緊急采購，3分鐘左右您將得到回復。