參數資料
型號： AMMC-6241
英文描述： 26-43 GHz Low Noise Amplifier
中文描述： 26-43 GHz的低噪聲放大器
文件頁數： 7/8頁
文件大?。?/td> 954K
代理商： AMMC-6241
7
Biasing and Operation
The AMMC-6241 is normally
biased with a positive supply
connected to both V
D1
and V
D2
bond pads through the 100pF
bypass capacitor as shown in
Figure 21. The recommended
supply voltage is 3 V. It is
important to place the bypass
capacitor as close to the die as
possible. No negative gate bias
voltage is needed for the
AMMC-6241. Input and
output matching are achieved
on-die, therefore no other
external component is required
besides one 100pF bypass
capacitor for the main supply.
The input and output are DC-
blocked with internal coupling
capacitors.
No ground wires are needed
because all ground connections
are made with plated through-
holes to the backside of the
device.
Refer the Absolute Maximum
Ratings table for allowed DC
and thermal conditions.
Assembly Techniques
The backside of the MMIC
chip is RF ground. For
microstrip applications the
chip should be attached
directly to the ground plane
(e.g. circuit carrier or
heatsink) using electrically
conductive epoxy [1]
For best performance, the
topside of the MMIC should be
brought up to the same height
as the circuit surrounding it.
This can be accomplished by
mounting a gold plate metal
shim (same length and width
as the MMIC) under the chip
which is of correct thickness
to make the chip and adjacent
circuit the same height. The
amount of epoxy used for the
chip and/or shim attachment
should be just enough to
provide a thin fillet around the
bottom perimeter of the chip
or shim. The ground plan
should be free of any residue
that may jeopardize electrical
or mechanical attachment.
The location of the RF bond
pads is shown in Figure 12.
Note that all the RF input and
output ports are in a Ground-
Signal-Ground configuration.
RF connections should be kept
as short as reasonable to
minimize performance
degradation due to undesirable
series inductance. A single
bond wire is normally
sufficient for signal
connections, however double
bonding with 0.7 mil gold wire
or use of gold mesh [2] is
recommended for best
performance, especially near
the high end of the frequency
band.
Thermosonic wedge bonding is
preferred method for wire
attachment to the bond pads.
Gold mesh can be attached
using a 2 mil round tracking
tool and a tool force of
approximately 22 grams and a
ultrasonic power of roughly 55
dB for a duration of 76 +/- 8
mS. The guided wedge at an
untrasonic power level of 64
dB can be used for 0.7 mil
wire. The recommended wire
bond stage temperature is 150
+/- 2C.
Caution should be taken to not
exceed the Absolute Maximum
Notes:
[1] Ablebond 84-1 LM1 silver epoxy is
recommended.
[2] Buckbee-Mears Corporation, St. Paul, MN,
800-262-3824
Figure 18. AMMC-6241 Simplified Schematic
RFout
RFin
VD1
VD2
相關PDF資料
PDF描述
AMMC-6241-W10 26-43 GHz Low Noise Amplifier
AMMC-6241-W50 26-43 GHz Low Noise Amplifier
AMMP-5618-BLK 6-20 GHz General Purpose Amplifier
AMMP-5618-TR1 6-20 GHz General Purpose Amplifier
AMMP-5618-TR2 6-20 GHz General Purpose Amplifier
相關代理商/技術參數
參數描述
AMMC-6241-W10 功能描述:射頻放大器 LNA MMIC 30-41GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
AMMC-6241-W50 功能描述:射頻放大器 LNA MMIC 30-41GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
AMMC-6333-W10 功能描述:射頻放大器 LNA MMIC 17-33GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
AMMC-6333-W50 功能描述:射頻放大器 LNA MMIC 17-33GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
AMMC-6345 制造商:HP 制造商全稱:Agilent(Hewlett-Packard) 功能描述:20 - 45 GHz Driver Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*